I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I'm looking for a gateway (or BLE 5.0 device that can connect to a gateway, e.g. USB dongle) that uses the nRF52 series solutions with an amplifier that brings the transmission...
Sir
We have a client that is using two NINA B3 (uses a NRF52840), one central and other peripheral. The peripheral is sending advertising packages, but the central is only...
Hi I'm very interested in studying this protocol, and I'm testing with nrf52832 kit development, loading the example "bike power meter tx" and app on android "ant + plugins...
Hi,
I'm using NRF52832 and a core adaptation for Arduino IDE. In my project I'm using both TWI and SPI interfaces. If for TWI I manage to reduce the current during sleep...
Hi everyone,
I am using a chip nRF52832 reading data from LIS2DH12 via TWI (all in a custome boad), then data will be send to Master nRF52832 DK ia BLE_NUS. However, when...
I have a new nRF52840 Dongle which seems to have either had a hardware failure while updating its bootloader or the updating was unsuccessful and now the device does not flash...
To do some test, I need micros(). This is the reason why I couldn't use RTC or app_timer.
When I tried timer example(nRF5_SDK_12.2.0_f012efa\examples\peripheral\), I could...
Hello, I need to use PWM to control GPIO and integrate it to work on simple COAP server app using nrf52840 DK.
I used "pwm_simple" example from SDK (not Thread/Zigbie SDK...
Hello.
When I try to initialize provisioning bearer gatt with turned on the proxy, provisioning bearer is reconfigure the mesh_gatt which it will not work with proxy anymore...
Hello,
I started developing a Thread-Solution with my NRF52840-DK. Now I'm searching if there is a Message Sequence Chart (like for the BLE solution) also for the Thread...
Hi,
I'm testing the below example code, found on devzone, on mesh sdk 2.2.0.
I'm experiencing a strange issue on the read side. On the first read after the write I always...
Hi,
I have an application (central mode) which regularly connects to a number of clients, read characteristics and then disconnects again.
Whenever there is an unintended...
I'm have nRF52 DK, wish use nrfutil (v4.0.0) to update target firmware. Works fine when using -n "Target Name", but I get a "Device not found" when trying to use parameter...
I have a custom designed PCB that has the nRF52832 (taiyo yuden EYSHCNZWZ) on board.
When I flash the board using pogo pins and the jlink (debug out) from a nRF52DK, everything...
Hi,
I am using the nRF51 dongle to connect and subscribe to specific characteristic and i am getting notification correctly but when subscribing to another notification...
