I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I am trying to measure and characterize expected battery lifetime of my design. I've noticed that as the effective Connection Interval goes up, so does the Rx current peak...
After init I2C channel
#define TWI_INSTANCE_ID 1 // because SPI0 share same reg add with TWI0 we change and enable TWI1
#define MAX_PENDING_TRANSACTIONS 5
NRF_TWI_MNGR_DEF...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
I will like to know if the nRF52832 is capable of working properly when placed in series with a 30 Ohms Resistor ( which is the battery resistance for our application) at...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
Imagine following use case:
Alice has a peripheral bonded with Alice's phone (central)
On the peripheral, Alice switches to a "guest mode" which disconnects from Alice...
HI
UUID scan filters are set and enabled.
I was capturing peripheral device MAC id via ble_evt_handler.
i was expecting filtered devices should be visible but when i...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
