Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
nrf52832, SDK 15.0.0
I develop the project based on the example 'ble_app_buttonless_dfu'
But when I want to add some peripherals, such as SAADC, SPI and PPI, and some...
I'm seeing strange corruption in the nrf52840 virtual COM/UART (the one that goes through USB and the JLink interface MCU).
The nrf52840 is running the UART serialization...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I would like to use the time library to manage multiple times with different timezones in my embedded system.
I have already seen the ble_app_cts_c example and the nrf5...
this is vishal from VVDN tech working as a Hardware design engineer .
In our project we are going to use 10k module of LTE EC25E.
So we need step file from your side ...
Hello,
In ble_app_blinky code,I cant understand this line "#define APP_BLE_OBSERVER_PRIO 3" and what does the value 3 represents here??. Is this value constant or can be...
Hi,
We have been developing our system around nRF52840 and we are now looking closer into the real-time performance of the MCU & SDK. The scenario is simple: a signal ‘YELLOW...
I am trying to add the valid range descriptor to my measurement interval characteristic in the Health Thermometer. This is a necessary step as my measurement interval characteristic...
Hi
I am using the ble_app_blinky's lbs application, as found here in the 14.2 service
C:\Eran\Software\Nordic\Packages\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hello,
We have an application on Iphone running with our custom service :
uuid : 0000fdF9-0000-1000-8000-00805f9b34fb
and our characteristics :
char-handle 0x16...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
Hi Everyone,
I have two task in which i am receving data from bluetooth and if i receive a particular hex value , i want a task(which is Toggling LED State) to run on...
Hi,
I am trying to to port ble-mesh code (serial example) into ble_app_uart. I am using nrf5_SDK_forMesh_v2.1.1 and nRF5_SDK_15.0.0_a53641a on DK-N52832.
After merging...
Hi,
Earlier today the forum appeared empty and none of my old posts were visible under profile > questions. Another user also had this issue. The front page looked like...
