Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi.
I am using the nRF52840 DK board and have integrated the SDK15 ESB_Rx example with the HID example.
The nRF52840 DK board has two USB ports. (J2, J3)
J2: Firmware...
Trying to track down an issue with IOS disconnecting shortly after connection when using NRF Connect, LightBlue doesn't connect at all.
We have a few GATT chars with...
Hello,
I am facing an issue when trying to use the example flash_fstorage_example in SDK15 with the softdevice. According to the documentation, using the reading and write...
I am testing SPIS to transmit mass of data(255 bytes each call) from nrf5 DK.
I found SPIS data shifting randomly.
The testing data is 0x88 but sometimes can get 0x44...
Datasheet of the Sensor:
www.ctconline.com/.../1_VS_TA102_DS.pdf
Accelerometer Out = 100mV/g =equivalent to=> +/- 8Vpk-pk
Temperature Out = 10mV/°C
Please provide...
FDS uses softdevice API. SDK 14.0.0
FDS writes are all successful for the same file id and different record keys until the flash is full
fds_delete_record() is called...
Hi,
I'm developing software for the nrf52832. However, I can't use the SDK of Nordic for several reasons.
In the code, I would like to save a small amount of data...
I tried to assigned each device to different group(subscriptions) by the following code segment.
for (uint16_t i=0; i < devCnt; i++) {
......
ERROR_CHECK(config_client_server_set...
Hello Everyone,
I am trying to incorporate NFC-BLE pairing feature in my ble_app_uart example. I have imported all the necessary files to the project and have installed...
Hi,
I am working on the project as a MultiLink example. My environment is using nRF52840DK & Softdevice 6 & SDK15.
I am trying to make multiple connections and communicate...
Trying to understand how the Device UUID is derived.
in iOS, Device UUID: FC7C7422-2BCF-894B-E848-855791DD3DD9
in RTT:
DEVICEID0: 0E064007 DEVICEID1: 14669F75 DEVICEADDR0...
Hello.
Hello.
I am trying to install pc-ble-driver-js on my computer but it fails to install. If anyone could guide me how to install it, that will be appreciated...
I'm having a strange problem where the Supervision timeout does not seem to work right at the point the connection is initiated (sd_ble_gap_connect() was called but BLE_GAP_EVT_CONNECTED...
I'm using the SPI in slave mode and have a very high power draw: > 2 mA. The issue happens both in my application + custom board as well as with the dev-kit + SPIS example...
Hello
I just have some small queries.
Let's say that I am scanning continuously for advertisement packets. I think the MAC address of the devices sending these packets...
