Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Minor nitpick:
The PS_v1.0 datasheet says that "see the Reference Layout section on the Downloads tab for nRF52840 on..."
There is no Reference Layout section on the Downloads...
I am working on a BLE bootloader using SDK 14.2.0 on an NRF52832 device, using softdevice version 5.0.0. I am able to get the bootloader up and running, and I am able to see...
Pre Conditions:
1. As soon as the connection is established the App start a timer to disconnect the link using sd_ble_gap_disconnect
2. The app timer has the same timeout...
Hello,
I'm searching the possibilities of Thread mesh network. And I want to minimize the size of border router as small as possible. Have you considered to port the border...
Hi,
I'm having trouble writing to a characteristic when operating as a central. I'm sure it is just a lack of understanding on my part but neither the SDK documentation...
Dear Sir,
In the twi sensor example code in sdk14 of nrf52832 the sensor LM75- B is mentioned.Please tell me that can I use LM75-A. with the same code.
Warm Regards, Manoj...
Hello,
First of all, i work with Linux Mint (Ubuntu 16.04) on my PC. For the WIndows Tools i do use Virtualbox on a Win7 system (can this cause any problems?)
i do...
When I add a PWM or simple timer to a uart example I get the error in Keil.
Simple timer: I added app_simple_timer.c to the library, I added the #include "app_simple_timer...
Hello,
We are currently trying to find our way in all the documentation and procedures required to qualify our product with the Bluetooth SIG. I am using their Launch Studio...
the interval parameter setting in application don't take effect,,, device still run with DFU-bootloader's connection interval setting.
i use nRF5_SDK_13.0.0-1.alpha.
...
Hi, everyone.
I have developed own application base on ble_app_uart.
But now I have to upgrade OOB pairing with NFC.
I have some problem.
First, I have to use...
i want to pair the device by one key. push the key ,the host pair the device. if not to push the key, the host can not pair the device.
the key is yes/no
how to set ?
Are there any library for One Wire protocol?
I found for using Arduino, but we use nRF5 DK with Segger Embedded Studio. We wil use DS18B20 standalone sensor.
I need a module that I can poll over SPI from my host MCU an output of a FIFO buffer of incoming packets (MAC address and RSSI) on channel 37 Bluetooth. Or a module where...
