Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
i search a FSK tranceiver with a ADC readout for a experiment.
I need the raw ADC ("audio") signal for a external signal processing.
Please help, most of the wireless...
I want to transfer application over the air(OTA) to NRF51822, with using nrf-toolbox in android mobile so please tell me step by step procedure. and how to setup nrfDK to...
hello every,do you have the same question?
i delete the bsp relevant document,then i find that when i disconnect it from APP,it delay to Generate disconnect events. i use...
I'm trying out 6lowpan examples in the IoT SDK, and while everything works,
if I want to disconnect by running:
echo "disconnect 00:50:49:71:3b:44 1" > /sys/kernel/debug...
I have compiled the following list of error that are given by BLE Stack from the ble_app_gls code.
I would like to know what action needs to be taken on reception of all...
Hi everybody!
I want to do a connection between two BLEnano, one is the mater and the second the slave.
I have programmed the two BLEnano using the Arduino IDE and libraries;...
Hello,
I was wondering what is the best option/way to merge two functionalities which are developed in different examples of the nRF52 sdk12.2.
For instance, I would...
hi,
my device is nrf52832
i run my spi sd card driver fine in debug mode, but when i download it ( F8 ), it can not work!
so my question is what is the difference...
Hi,
I need to monitor radio channels and find the best one (with lower background noise) to use.
Is there any way to measure radio signal level in a particular frequency...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
I'm trying to get a simple "Hello world" program to run on the Nordic ID Medea.
As soon as I start debugging I get the error "The bootstrap could not be loaded".
Any idea...
I follow this:
developer.nordicsemi.com/.../a00092.html
Creating an image file
The format of the firmware image that you use to update the device firmware depends on...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
At the moment I am working on a project that uses the nRF52328 acting as both a peripheral and central to connect 3 separate devices intermittently. I am storing their bonding...
