I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I have some problem in DFU.
I ask this again.
I did as below.
Key generation
nrfutil keys generate c:\vault\priv.pem
public key generation in...
Dear Nordic Team,
I can't launch Sniffer on PCA10000 using MCP nor on PCA10040 using nrfConnect. In case of MCP I get "No response from master emulator" and in nrfConnect...
Hi,
is someone of you aware of a portable (Win, Linux, OS/X) GATT client library, prefereable with C++ binding? The only one, that I've found so far is Qt. What do you use...
I have been using nRF8001 equipped Arduinos for a few years now with great success. I exclusively use apple software on the other end. I have a new application that will required...
i want use a 9 axis IMU sensor (3 axis accelerometer,3 axis gyroscope and 3 axis magnetometer) in nrf51822 is it possible and how the transmission of values takes place.....
Hi,
I'm using the bootloader in nRF5_SDK V12.0 with nRF52832. I have some problems want to know:
How to make it run application first after I program softdevice...
I notice that the track which runs from P0.11 (E4) is connected to GND at pads C3 and C4. Is this intentional? If P0.11 is required for GPIO usage, is it necessary to go to...
I am trying to update my project to SDK 12.2 which was released this week and I am getting a ton of compiler errors with the FreeRTOS source files. For example, I try an compile...
I'm a begineer in nRF52DK and S132.
I am trying to make an application code to enable link layer control procedures at any time in a connection state with the nRF52DK and...
hello everyone，
Which APP demon is the most stable APP？
I use nrf-master APP to test the blue device，it can connect very well。but when I use uart-app ， it can't connect...
I notice that if Make virtually any of the SDK12 armgcc examples that I get a warning that 2 include folders do not exist
e.g.
../../config/ble_app_hrs_pca10028_s130...
BLE UART run example runs in debug mode and able to see the BLE in the nrfconnect
using Jlink debugger
When the Jlink debugger and power supply is provided we are not see...
Hello,
I am currently using the GPIOTE Driver (nrf_drv_gpiote) to detect external interrupts from a sensor on a custom board using the nRF51822 with the S130 v2.0.0 SoftDevice...
Hello,
I've an issue with several smart-phone models when I use the softdevice S130 v2
I did tests with PCA10028 and the example "ble_app_bps".
I used softdevice...
