I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear Nordic Team,
Thanks for Support.
I am worked DFU service in SDK11 it was working fine. Now i am DFU service work with SDK12 using nrf51422 DK. Initially update...
I am getting an error on a connection via the ble nus service that is causing me to scratch my head. If I suppress the error the connection seems fine and I don't notice any...
Hello,
Is it possible to send as central (and data server) one notification to all connected peripherals at once? Or is it necessary to send notification to every peripheral...
Hi all, in my project I have a input pin and out pin whenever pulse is raised on input pin I need to set out pin exactly after 8.3ms.
For these I'm using ppi by configuring...
Hello,
I'm trying to upgrade my SDK v11 project to SDK v12 project and I just got sober from idea that I switch SD and update "components" folder.
For example I was using...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'm sorry for general question, but I need it for my calming down.
I'm delving step by step go throught header files into origin definition of function for understanding...
Hello,
I'm implementing bonding feature on nRF52 with SDK_0.9.2.
I found a tutorial which is devzone.nordicsemi.com/.../ .
I followed this tutorial and then tried to...
I have a sensor HTS221 that I would like to power from an nRF52832 I/O to allow programmatically resetting the sensor. Looking at section 20.4.1 GPIO Electrical Specification...
We have bots (what I'm calling our device for this question) that play both the peripheral and central role depending on their context (not unlike the relay example; except...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
HI,
Currently I try to run example/iot/tcp/client in nrf51 iot sdk on nrf51-dk board. Then on server side, I use "ping6" command to test the data sending and receiving...
Hi, Very happy to note that you are planning to release source for nRF Connect for Desktop soon. Do you have an updated timeline on that?
Also, I am trying to use pc-ble...
Noticed this for gcc with -0s optimization an application fail to save a bonding data. It is caused by byte alignment of
static uint8_t buffer_memory[(n_blocks) * (block_size...
