I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hardware Config : nPM1100-EK (PCA10123 0.8.0, date code 2022.25), SW1 = GND (automatic), SW6 = VSYS/VSYS (VOUTB = 3.0 V setting), VOUTB measured 3.12–3.13 V at 3.7 V in using...
Hi, We are currently developing our own NTN device using NRF9151 SIP LACA 1A. I was able to flash the NTN modem firmware long with the serial modem firmware to our custom...
We are using a WM8960 audio codec with the nRF5340. When the codec works at different sample rates, the noise level changes significantly:
8 kHz: high noise
16 kHz:...
I'm using nRF Connect SDK (NCS 3.1.1) with LVGL and newlib in a application. I encountered two related problems that I believe are caused by a conflict in the Zephyr LVGL...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hello,
after having a product using a nrf52832 MCU for a while in production using nrf connect sdk 2.5.1, we now wanted to supply a first firmware update. However, while...
Title: Bluetooth Mesh PB-ADV provisionee keeps a 3 s transaction timeout after a device-initiated link close (NCS v3.1.1) NCS version: v3.1.1 (also present in v2.9.0) SoC...
NCS SDK 3.4.0 NRF54LM20DK
The nRF54LM20A data sheet warns against using the same RAM subordinate by more than one bus manager. From section 4.2.1,
Avoid situations where...
Hello,
we are designing an open-hardware set of motion sensors for veterinary gait examination, NIC-Strelka: 1–32 identical units on an animal, each with an nRF54LM20A...
Hi! I'm designing a custom board based on nRF9160 and I have some questions regarding the GNSS antenna circuitry. The antenna I'm planning to use is Molex 206640, as I saw...
I've updated my project from 2.7.0 to the latest (3.4.1), which was an experience. However, I've got it compiling now, but I'm getting the following error in the SW PWM driver...
Hi Nordic team,
I am measuring System OFF current on three boards that all carry an nRF54L15, running the same application built with nRF Connect SDK v3.2.0 (Zephyr sys_poweroff...
My desired work flow is the following.
Input: Two electret microphones -> Audio ADC -> I2S Stereo -> nrf5340
Processing: Buffers (10-50 bytes) channel 2 to create delay...
