Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
Hi, We are using `fota_download` library on our nRF9161 design running mfw-nrf91x1_2.0.1 to download a firmware upgrade image from our Amazon AWS server location. When trying...
Hello, I am currently using (\nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio\receiver)routine to develop.I want to check if the first N bytes of the received packet are...
Hi! I am using nrf32840 with free rtos,
and I have a loop that do the following
for(;;){
vTaskDelay(pdMS_TO_TICKS(intervalTime)); // go to sleep due to portSUPPRESS_TICKS_AND_SLEEP...
Hello guys, W are using the nRF52840 development kit in our project, we received the development kit today and when we powered the kit to my laptop(Acer nitro 5) using a micro...
Hello guys
I'm using nRf52840 development for my project, when trying to connect using a micro USB to the laptop, the J Link drive is not being detected on my laptop(Acer...
Hello.
In the BLE software being developed, the device uses nRF52840, s140 v7.2.0 or v7.3.0, and I am building a system that periodically sends a beacon (ADV_NONCONN_IND...
I am trying to program nrf52840 to print acceleration from mpu6050. But when I build the project, I get the error - undefined reference to `nrf_drv_twi_init'. Here is the...
Hi Support, we are using custom hardware and the follwoing versions:
1. modem - 1.3.4
2. nrf-sdk - 1.9.0
3. Zephyr - v2.7.99
Our application is based on the gnss sample...
Hi
We built an application that bases on the sample application "central_and_peripheral_hr" with NCS v2.7.0 and nRF54L15.
In this application, I tried to manually start...
Hi,
I am facing a problem with connecting nRF9160-DK to the cellular network. waited for more than hour for connection but always showing "Not registered, attaching or searching...
Hello,
For one my projects, I am planning to implement TensorflowLite in nrf5340 board. Could you please recommend some sample projects which I can take as reference.
...