Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi guys , another question here regarding Cmock and opaque types . I am currently trying to mock a function with an argument that contains the type "struct bt _conn " . However...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
We are using modem firmware 1.3.5 on nRF9160.
When packet loss is high, we sometimes see connection resets (NRF_ECONNRESET) reported by the modem that don't seem to be explainable...
Hi,
I try to use CPSMS command to reduce the power consumption. The idea is to send a MQTT message every 10min and have the GPS coordinate every 5 min.
The NRF9160 is...
Hello,
I have 3 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to stream left/right audios and I'm able to achieve it.
https://developer...
Hi,
I am investigating low power modes in the nRF9160. I am currently using the GNSS sample code and getting around 36mA. Is there any way to configure the base code to...
Hello,
I have implemented an application for nRF5340 chip derived from the Zephyr AWS IoT MQTT sample. The application is based on W5500 Ethernet driver so the idea is to...
Hi,
I’m trying to have two nrf9161s exchange data back and forth as quickly as possible. Initially the first radio is transmitting, and the other is receiving (3 sub-slots...
Hi! Can you please help me identify what is causing this issue and/or provide more info about this:
[00:04:23.038,330] \033[1;31m<err> bt_sdc_hci_driver: SoftDevice Controller...
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. My app configures as BLE Peripheral. Now I want to keep track of the device names of connected...
HI Nordic support team.
I have a question relate to RSSI in proprietary_rf application.
We test on esb_low_power_ptx.
Can i read RSSI of esb_low_power_ptx?
thanks...
Hi,
Sorry for the very basic questions. I am new to nRF connect SDK.
I want to develop a ble custom central application with my custom characteristics. I started to look...
Hello!
I have an application using MCUboot and a single application slot. I want to use the Retention System to signal to MCUboot wether to boot normally or into serial...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...