Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Hi,
I am using a Proteus-e module from Wurth Elektronik for a project. This module contains a nRF52805 chip. I am using the nRF Connect app to send commands to configure...
Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
From "nrf_section.h" (__GNUC__):
Example for the section name " log_const_data ":
NRF_SECTION_DEF(log_const_data, nrf_log_module_const_data_t) //: extern nrf_log_module_const_data_t...
Dear,
I am using both nRF52840 UART (UART0 and UARTE1) on the nRF52840 DK.
The default pin assignement is used, such as
UART0 pins are TX/RX 0.6 & 0.5 and
UARTE1...
Hello!
I built the https sample app for the Sparkfun_I got run time errors.
my setup:
Updated Windows 11 Pro
SDK 2.6.1 and 2.8.0
How do I solve this?
"The Modem...
Hello,
I am facing an issue building the Matter light switch example for nRF5340 for ncs 2.8.0.
Include zboss_api.h is not working in zb_nrf_pwr_mgmt.c
Setup ...
I have an nRF7002dk & its datasheet mentions that there is a 64 Mb external flash memory. The memory is connected through a regular highspeed Serial Peripheral Interface ...
Hello, I want to configure the BMP390 using I2C on my custom board. However, when I try to read the CHIP_ID register, I am unable to get the default value, and the function...
"I added an endpoint called Matter Extended Color Light to the matter_bulb example. After compiling and flashing the firmware, HomeKit only recognizes and creates two dimmable...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
Hello,
We are facing an issue where the sum of count in BLE_GATTS_EVT_HVN_TX_COMPLETE events (member of the ble_gatts_evt_hvn_tx_complete_t structure) doesn't match with...
Hello
I am evaluating Wi-Fi location using the nRF7000 and nRF9160.
For the initial test, I used the nRF7002 Expansion Board. I soldered wires to it and connected them...
