I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
My nRF52 DK has PCA10040 V1.1.0 2016.34 682272915 on a label.
It works fine when connected to my laptop over USB. If I try to power it from the coin battery underneath though...
Hello, we are using a radio module with the nRF51822 for our telemetry system.
In order to conduct the EMC test of EN 301 489-1, I would like to clarify the 6dB bandwidth...
This is a duplicate of this issue of pc-ble-driver-py repository.
While using pc-ble-driver-py on MacBook without problem, I face Error 13 when opening device on Raspberry...
Dear friends,
I am connecting multi peripherals to single central, and i am using nrf53832 devices. How are the link resources shared among multi peripherals? In addition...
Hello,
We are using a nRF52832(peripheral) on a custom board and connecting it to a nRF51822(Central). The nRF52 has one GPIO connected to a button which is used to power...
I have an application that is using FDS to save settings to flash. The application works great as a standalone application, but when I try to use a custom bootloader (same...
Hello!
I am looking for the best solution in terms of power consumption to transmit data with the nRF8001 and have a few questions:
1) I read in another discussion that...
Hi,
I am writing a DFU Application on NRF52 and Android (based on NRF Toolbox). I would like to give user an ability to abort upgrade, however when i send abort from android...
Hi Nordic,
I am currently looking at using the link context manager introduced in SDK15.0 . I can see it could be useful for my application where each connection needs a...
I use the sdk14.2 nrf52832 as the primary end, the two iphone phones as slaves, to establish a connection in most cases because of the 0x3e error to connect several times...
HI WE HAVE DEVELOP AN BEACON USING NRF52540 IN THAT WE WANT RETAIN UUID, MAJOR ,MINOR AND NAME WHILE POWER OFF
for this you suggested flash data storage and flash write...
Hello to all,
I am using nRF52832 sdk15.0 version with SES IDE. I want to find adverting with short for e.g.--->
we have BLE app_uart peripherals and one multilink central...
Dear Nordic engineer,
Here is a question when we use the chip's automatic response function, the MCU PRX can download the packet, but PTX can not receive the ACK signal...
