Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
For the connection event collision, I have some doubts, I hope to get help in devzone
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.s132.sds...
Hi, everyone,
We develop BLE project including DFU bootloader.
But to use the standard bootloader "as is" it is not possible for us. Due to this problem we must make some...
On Apple platforms, It's pretty easy to end up in a situation where there is bonding information on the Nordic but that information has been deleted from the host. All you...
Hello,
I am using sd_power_system_off(); sfunction to put the MCU in sleep mode. I have to wake up events. One is NFC and the other is GPIO. Both wake up functions works...
Hello all, Nordic Team
i've a question regarding the format of the nonce used within CryptoCell Library v0.9.0.a
What i've learned so far is, that CRYS_AESCCMstar requires...
Hi
Is there any ready-to-use SDK example that demonstrates how the 2MPHY functionality is exercised on the nrf52810? We have gone through SDK15.0.0 but it appears that...
hello all,
i am developing with BLE_NUS.
i want to sent the string data on BLE using UART example.
string data length is over 300 bytes like belows.
55AA FFFF...
Hi guys
I am using SDK 13 and a nRF52, so on my application, I require a lot of RAM usage transfer small files in order of 10-30kB, is there way to see the RAM available...
i want to use the nordic nrf52840 in my new beacon design. however i dont see many others using it. i downloaded the DK files from nordic to figure out the feasibility of...
Dear Nordic Team,
Thanks for supporting. Now i want to integrate GPIOTE with BLE UART example. When i call gpio_init(); this function got error like below image.please support...
Good morning,
I am trying to get the lowest current during system OFF (no RAM retention, no wake-up sources configuration) on 52840 PDK. The spec says that the OFF current...
Hello,
i am working with a custom board, based on nRF52832, running the Bluetooth Mesh SDK v2.0; the board is equipped with a SoC that communicate with the nRF52 using the...
I am using the Windows version of nRF Connect v2.3.2. Aborting the DFU process does not work in the following use case:
- Connect to a nRF52832 advertising as DFU (for example...
I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection after disconnect For example...
