Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have initialized SPI0 master by this code:
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(0);
...
nrf_drv_spi_config_t spi_config = NRF_DRV_SPI_DEFAULT_CONFIG;...
Recently I have been working with the serial bootloader from SDK 11. I can upload a softdevice, and supporting application using this bootloader without issue, as long as...
I started working on mesh 51 series ,
Points for which we need inputs
Data packet size for transmission
Process for association and address assigning during commissioning...
Hi,everyone
I am using S132 and SDK13 to set two peripheral links,now i want connect two centers using different connection parameters at the same time,for example,connect...
Hi,
Can the nRF52832 support higher data rates:
UART TX baud rate of more than 1Mbps, such as 3 Mbps without bitbanging.
TWI of 1MHz
any trick to get them...
Hi,
I recently purchased the NRF52 DK. I'm using the ble_uart_example for the SDK 11. I'm using the softdevice PCA10040.
I noticed the the SDK 11 includes the RTT c...
I want to use the nrf52840 with DCDC in high voltage mode to drive the circuite directly from a LI-ION battery.
Is there any reverse current protection built into the chip...
When you start a receive task, what will the radio do if the HFXO is not stable? Not begin to ramp up until the HFXO is stable, OR begin to ramp up but not become active until...
nrf52832, returns an error even with parameters
IROM1: 29000 57000, IRAM1 3CC8 C338, softdevice_enable() works without errors.
#define PERIPHERAL_LINK_COUNT 1
#define...
im working on nrf51822 using sdk 9 ....i completed bonding using ble proximity example without privacy key.....now i wish to add privacy key ..what all changes i have to make...
I'm using the with SDK version 13.1.0 along with S140 SoftDevice v 5.0.0-3.alpha and trying to utilize the Bluetooth 5 Extended Advertising feature.
The function ble_advdata_set...
I'm periodically polling a TWI sensor with a blocking call, as in
ret_code_t err_code;
m_xfer_done = false;
err_code = nrf_drv_twi_tx(&i2c, address, subAddress, 1,...
My external application processor UART, every 5 ms @ 19.2 KBPS transmits a byte to UART RCV of NRF8001, which needs to convert this to BLE and then transmit to a cell phone...
Hello All,
I am working on nrf52832 and i designing the custom board for the same for my application , which all pins i need to select as programming pins to dump the code...
