Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi all,
I would like to design a product based on the nRF52832 chip. The board should have an accelerometer, a charging circuitry for a LiPo and some additional components...
Hi there,
I am done with TI and the new IDE and Stack 2.2
May be anybody can point me to the right IDE and chip to replace my TI CC2640 4x4 designs to Nordic semiconductor...
Hello,
I would like advertise for an unlimited time.
Why value 0 in ble_gap_adv_params_t::timeout don't work ? Device don't advertise anything. It works fine with a positive...
In the nrf_drv_gpiote in SDK 11.0, I can only find a function to get the address of the out task for a gpiote channel. Shouldn't there be a similar function to get the addresses...
I am working on nRF51822 ble_app_bps and I want to use Estimote SDK to monitor beacon on the background.
I also changed UUID, Major, Minor value: UUID.fromString("00001810...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
Hello Nordic Support Team,
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. Since there are more than 7000 devices...
I'm trying to get the default SDK v12.0.0 BLE App UART running with SoftDevice S130 v2.0.1, with minimal customization (I just enable the Peer Manager module in sdk_config...
Hello,
I am using i2s through the driver : "nrf_drv_i2s". After playing a song, I have a residual current consumption about 1mA unless I call nrf_drv_i2s_uninit every times...
Hi everyone!
I flashed an application with the help of DFU bootloader. The application runs for the first time . The application contains a service that lets the application...
Has anyone had the problem recently of trying to make or debug from within GCC and hitting an exception immediately? I believe I picked up an update to Eclipse because after...
Hi, I'm using SDK12 and I'm trying to implement button debouncing. I have initialized one of the nRF52 board buttons using app_buttons.c. In the infocenter I read that debouncing...
Hello,
I am using ble_app_template project. I want to add uart in this project. So I am referring uart project from peripherals. Now in ble_app_template project under nrf_drivers...
Hi,
recently I experienced a strange behavior on the nRF51 chip, that is at a certain point some gpio lines remained held high, even if the firmware set them to low (both...
