Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hi, this is a bit of a vague question. I am not exactly looking for an answer, i was just wondering if anyone had a similar experience.
I am using nrd5340-dk and my application...
Hello, I have stumbled upon a case exposing a bug in your lib/date_time/date_time_core.c.
In my case the modem re-registered and got a time from the network (%XTIME) right...
Environment : - nRF Connect SDK v3.4.0. - CONFIG_SPI_NRFX_SPIM_RTIO=y. - SPI_HOLD_ON_CS is not enabled. The same completion ordering is present in upstream Zephyr main : https...
SDK: nRF Connect SDK v3.4.0 (LTS) Library: nrf/lib/sms
Summary
sms_register_listener() is documented to return a listener handle or a negative error code. In practice...
Hi,
Initially, I can send and receive AT commands. But after sending the power-down commands
sequence from "Getting Started with nRF93M1 DK v0.4"
I could not receive...
Hi all,
Quick question on NFC design practice.
I am using the nRF54L15 NFC in tag emulator mode (differential), with the following setup:
Antenna: Molex 1462360051...
What high-temperature storage (JESD22-A103) and temperature-cycling conditions was the nRF9151 qualified to (temperature, duration, cycles)? Your DevZone forum mentions 125...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi Nordic Team,
Does the reset of 54L15 need to be handled? Still pull up a 1k resistor. Also, do I need two wires for debugging?
The customer has another question....
When transitioning from ncs v3.3.0 to ncs v3.4.1 noticed a warning about CONFIG_BOOT_ECDSA_CC310 being depreciated when building MCUboot. The release notes suggest using PSA...
I am using display example code from zephry repo. ( zephyr/samples/drivers/display at main · zephyrproject-rtos/zephyr ) . Connected to a nRF7002 dk , i am using EA W096016...
