I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hardware Config : nPM1100-EK (PCA10123 0.8.0, date code 2022.25), SW1 = GND (automatic), SW6 = VSYS/VSYS (VOUTB = 3.0 V setting), VOUTB measured 3.12–3.13 V at 3.7 V in using...
Hi, We are currently developing our own NTN device using NRF9151 SIP LACA 1A. I was able to flash the NTN modem firmware long with the serial modem firmware to our custom...
We are using a WM8960 audio codec with the nRF5340. When the codec works at different sample rates, the noise level changes significantly:
8 kHz: high noise
16 kHz:...
I'm using nRF Connect SDK (NCS 3.1.1) with LVGL and newlib in a application. I encountered two related problems that I believe are caused by a conflict in the Zephyr LVGL...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hello,
after having a product using a nrf52832 MCU for a while in production using nrf connect sdk 2.5.1, we now wanted to supply a first firmware update. However, while...
Title: Bluetooth Mesh PB-ADV provisionee keeps a 3 s transaction timeout after a device-initiated link close (NCS v3.1.1) NCS version: v3.1.1 (also present in v2.9.0) SoC...
NCS SDK 3.4.0 NRF54LM20DK
The nRF54LM20A data sheet warns against using the same RAM subordinate by more than one bus manager. From section 4.2.1,
Avoid situations where...
Hello,
we are designing an open-hardware set of motion sensors for veterinary gait examination, NIC-Strelka: 1–32 identical units on an animal, each with an nRF54LM20A...
Hi! I'm designing a custom board based on nRF9160 and I have some questions regarding the GNSS antenna circuitry. The antenna I'm planning to use is Molex 206640, as I saw...
I've updated my project from 2.7.0 to the latest (3.4.1), which was an experience. However, I've got it compiling now, but I'm getting the following error in the SW PWM driver...
Hi Nordic team,
I am measuring System OFF current on three boards that all carry an nRF54L15, running the same application built with nRF Connect SDK v3.2.0 (Zephyr sys_poweroff...
My desired work flow is the following.
Input: Two electret microphones -> Audio ADC -> I2S Stereo -> nrf5340
Processing: Buffers (10-50 bytes) channel 2 to create delay...
