Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am trying to integrate buttonless DFU with FDS in ble_app_uart example from sdk 15.3.0. Merge hex was done properly which includes bootloader_settings.hex+bootloader.hex...
Hi developers and researchers,
I am working on a project in which multiple nodes are communicating with each other in p2p manner.
My goal is to implement a multiple access...
In the AWS IoT example I have been trying to add RSRP support (i.e. getting RSRP when sending my data packet).
I registered the handler/callback function in main after modem_info_init...
Is the mcuboot module compatible with RTT logging? I've setup mcuboot and my main application but cannot see any logging.
I have the following in both prj.conf & mcuboot...
Dear all,
I just writing a little piece of code (no softdevice, using sdk 17.00), that in theory toggle a led based on 2 compare (CC[0] and CC[1]).
The strange thing...
I am using SD 132 6.1.1 with a GATT server and when the client sends a Read Multiple Characteristic Values command, the nRF responds with Request Not Supported. I need to...
Hello,
I bought the Thingy 91 and tried to follow the instructions on the getting started page.
I started by downloading nRF connect - Programmer v 3.5.0. Then downloaded...
Hi,
I have noticed ever since I updated my nRF9160 DK modem firmware to the latest version v1.2.0 frequent registration dropouts and very sluggish MQTT performance.
My...
Hi, I recently bought a Nordic Thingy 52 and it looks great ! It looks like there is a decent mic and speaker on the device and I was intrigued if the device could act as...
Hello,
I am trying to do communication with external module using UART0. But when I connect pin P0.28 (RX of UART0) to external module to receive the data, there is no data...
Hello,
I am working with SPI on the Nordic nrf9160. I am currently on the DK.
The board I need to interface through SPI works at 25MHz (minimal frequency) and I would...
Hi everyone,
I know that I can configure the resolution of app_timer by adjusting the prescaler form sdk_config.h
However, what is the practical purpose of prescaler...
Hello,
I have created an empty mbed-os program from Mbed Studio, add sum LED on off logic and compiled against nrf52840dk board. After generating hex file, I upload the...
Hello,
I have created an empty mbed-os program from Mbed Studio, add sum LED on off logic and compiled against nrf51dk board. After generating hex file, I upload the program...
Hi, I want to write 510 bytes of data to my BLE Characteristics, so I set parameters ble_gatts_attr_t max_len as 510 and its variable length attribute. Also I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
