Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I try to load my nRF52 with app via ble from windows 10 laptop.
nRF52 dev kit is loaded with the Softdevice and Bootloader from nRF5_SDK_12.1.0\examples\dfu\ble_dfu_send_hex...
I have an external 32MHZ crystal on my custom board.I want to configure it to 32 MHZ external crystal to operate the chip. i changed the some register configuration in software...
all works fine with iphone that mean data stored, bond 's information that has been persisted during DFU processing.everything works with iphone. but when the device that...
Dear Nordic Team,
Thanks for supporting.
Now i want support for single channel(Ch 37) advertise , please support anyone. I am using ble_app_uart example.
My SDK : SDK12...
I'm running some stress tests on a nRF52832-based product, with the following setup:
- SDK 12.0.0
- SD 3.1.0
- Compatibility modes 1 and 2 enabled.
The device exposes...
hi ,
1. How do I migrate the codec OPUS part of SR3 ? I want to use it for audio. But migration always fails. Any migration examples?
2. How effective is ANR work? Are...
I use blinky_freertos demo on nrf52832,
now I want to disable FPU,
but when I disable FPU in Keil MDK option->Target Floating Point Hardware Not Used,
there is an error...
Hi,
i am using nrf52, sdk11 and S132v2.0.0. so i want to flash the hex file using OTA so that, i have create zip file using fallowing command.
**nrfutil dfu genpkg --application...
I've been trying to set up my nRF52 DK on my mac OS.
I followed all the steps to download the SDK (15.0.0), the Command Line Tools, the ARM GCC toolchain, and the J-Link...
Hi,
I have a few doubts regarding Subnet in Bluetooth mesh:
1) If a node including in 3 subnets, how it manages to switch between multiple subnets?
2) What are the various...
Hello,
I am using nRF52832, s132_nrf5.0.0_softdevice.
I am trying to build a ble gsm gateway.
I have 3 different peripheral devices. They have some services.
On my...
Hi
I am using SDK 14.2 secure bootloader with IAR and SES build. My IAR project is working with DFU upgradation but my SES Hex file is not working
Procedure Followed...
Hi, I use s132 and SDK15 to work with nrf52832. In code I set up RTC and CC to trigger every N ticks. It works as expected and time periods counted correctly. However, when...
