Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
Hello,
I am using the nRF51 transmitter_pca10028 example to try to communicate with legacy systems using nRF2401A.
I could achieve nRF51 TX to nRF24 RX successfully...
I would like to burst out 12 packets of 64 bytes and then go into RX mode immediately after for a single payload, followed by another round of transmissions. Is there a shortcut...
The data is sampled at 3khz, each sample is 2 bytes, connection interval is 7.5ms ,4packets per connection interval. The data is displayed on a graph with respect to time...
When I execute nRF5x_MDK_8_7_1_IAR.msi from the SDK 11 directory the files from the .msi are added to the IAR install directory, not the SDK. These changes are ignored when...
I was little bit confused between NRF24l01 and (+) plus version which is better . i want range of 900-1000m. which is best??
If i choose NRF24l01+ what are the ways to...
(/attachment/0495424521df76d5b8f8e66c969ed791)Hi,
I add ANCS Service into my Heart rate ref ble_app_ancs_c example code.
I use MCU nRF51 and SD130 in nRF5_SDK_11.0.0_89a8197...
Hello,
My device is based on nRF51822 SD110 v8.0. Softdevice is enabled, but no BT functionality used. I measure 2 different voltages with ADC each second with two channels...
I'm writing code for PCA10040 basing on UART/NUS example. There are no big changes: different UUIDs and just one characteristic for both reading and writing. I can connect...
This is a follow-up question from devzone.nordicsemi.com/.../
I finally got passkey support to work on ble_app_uart but don't quite understand the changes made to the code...
I am trying to add static passkey pairing to ble_app_uart in SDK_11 s130. To do this, I first implemented static passkey successfully in ble_app_gls using sd_ble_opt_set(...
Tl; dr
I tried to use OTA DFU with Public BLE Address, but I failed. Is this possible?
Details
Condition
I modified ble_app_hrs example like below (SDK11, pca10028...
I have a radio board using a NRF51822 with a custom radio protocol. I need a unique identifier, ideally 24bit, 32bit but be acceptable.
I notice in the parameters there...
I've looking through as much of the documentation I as I could to read more about the radio timeslot api.
I looked through the SDS document and the chapter on the Radio Timeslot...
I am able to use eclipse to run simple project, but after move the real one, getting lost of errors:
www.dropbox.com/.../Screenshot 2014-04-02 09.10.41.png
I add required...
