Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I've been working with SDK 7.0.1 and it seems there are some issues with device_manager_peripheral.c.
First off it doesn't compile out of the box, the debug code is turned...
In the document nRF51822-PAN v2.4.pdf, PAN #9 says that OUTINIT doesn't work,
"Initial value for GPIOTE output after configuration is undefined"
and example workaround...
SDK 7.0.1 is intended for version 2 (G0) chips, and the future. So it can't be used with earlier versions of the chips (like C0). So it shouldn't have workarounds for C0 chips...
I have recently begun running into issues related to the SPIS module on my nRF51822 S100 v7.1. Fairly often, between 10 and 20% of the time, the interrupt does not fire when...
Hi,
I am using TIMER2, GPIOTE and PPI to implement a 6250Hz square wave at a GPIO pin. I can successfully create the square wave on the GPIO pin. However, I would like...
Hi,
I want to use nrf51822 for implementing HID keyboard and mouse.
Can the application be configured for keyboard and mouse simultaneously ?
i.e hids_init_obj.is_kb...
Hi,
I am using nRF51822 and trying to use Ticker from mBed library.
I have issues when using Ticker and PwmOut.
How is implemented the Ticker functionnality into nRF51822...
Hi,
I want to make a pulse for buzzer and led.
I find a sample source(led.c) and the Nordic SDK.
It is good enough in case posivie and negative duty is same.
I need...
Hello ,
As mentioned in another question, I would like to use the nrf51822 SPI slave peripheral to benefit from the DMA capability although I want to behave as an SPI master...
I can't seem to find where/how the BLE address gets randomized so it changes periodically when using the BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE address type.
-It seems...
Are the OVERRIDE parameters useful in any way shape or form when using the NRF_2MBIT mode?
Is there any reason other than BLE compliance to use the OVERRIDE parameters...
I cannot uninstall MCP on my W7 x64 system using the normal control panel add/remove programs method. It appears that I need to re-run the original installer which I no longer...
Hej,
that might sound like a dumb question, but what is the minimal setup to program an nRF51822 SoC using the SWDIO/CLK ports?
What external hardware is required...
