I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I'm using nRF Studio Visual Studio Code. (SDK and Toolchain v.2.7.0) with the nRF7002 Development Kit. The Blinky example have worked fine and also the other things as shown...
I'm trying to run the vanilla HTTPS sample on the nRF9161 DK: sdk-nrf/samples/net/https_client/README.rst at 4b9841a28e97e9d61b93f8981375d644b9d04ea0 · nrfconnect/sdk-nrf...
I need to install the Direct Test Mode App to validate the direct test mode running on a custom board. On the version 5.1.0 of nRF Connect for Desktop all app installations...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
I am trying to use my nRF52840 as a sniffer and am attempting to follow the directions at:
Programming the nRF Sniffer firmware (nordicsemi.com)
Note that I have downloaded...
Hi,
I want to use a LNA for make our sensitivity better, Then i should to put a RF switch and have a control in sending and receiving, because when the device is in receiving...
I am developing a USB dongle (nRF52833) for computers and a controller (nRF52833). As a basic configuration, multiple controllers need to be connected to one dongle. Multiple...
Hi,
We have a custom board (powered by nRF52840 with Softdevice and nRF5 SDK 16) that has an external ADC module to sample 30 kHz ADC continuously for 1-2 seconds. What...
I encountered the problem trying a Matter OTA-update and and asking myself why the bootloader wouldn't apply the image:
I am using the partition manager and defining the...
After flashing the nRF Sniffer for Bluetooth on nRF52840 dongle, I want to flash it back with the programmer to use it in the nRF Connect App but it wont go in boot mode....
Hi. I did some testing with two nrf5340DK boards to check the accuracy of distance measurement with Nordic's nrf_dm app. Even in non-high precision mode the reading with ifft...
Hi.
Our company has a couple of different custom designed boards using the nRF52840 and powered by a battery. OpenThread is used for networking, and the devices are configured...
Hello, I got a custom board based on nRF52840. It uses extended BLE advertising to deliver a sensor data to the central hub with a frequency of 10 Hz. I've set the interval_max...
I have a question regarding DTM using nRF Connect for Desktop. It is my understanding that the signal generated does not have a BLE packet structure but it is a continuous...
