I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Im install nRF Connect SDK 1.5.1 trough nRF Connect 3.6.1 Desktop app to learn zephyr RTOS and switch from nrf5 SDK to it but there is some bug and "Configure nRF Connect...
Hello,
I just receive a PPK2 and looking at power usage/profile. Below is the captured profile when the application is run from the debugger and then detached. This captures...
Hello,
ncs1.5.0
As shown in the question,
I use rtc to generate a 1kHz square wave, and use an oscilloscope to measure only 964 Hz.
Is there a problem with where I...
Hi.
I am using the oberon crypto backend module to use LESC in the application firmware. (I referred to the GLS example)
And I am trying to add a boot loader to use DFU...
Hello all, we are trying to set up a project with a nRF52840 chip in combination with 2 Acconeer A111 sensors. So far I have worked with a nRF52840 development kit and the...
Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello Nordic,
I am using Nordic 52840 (SPI Master) with Intan RHD2216 (SPI Slave) to get data through SPI from the Intan chip.
I have used the Nordic software development...
Dear friends:
I flashed a mesh serial example. I scand mesh beacon by the function "scan_start()". As you can see in below code, I got two uuid device, I want to select...
Dear friends:
I flashed the serial mesh example from Mesh SDK and contact the DK with pyACI according to the guide Using serial interface for provisioning and configuration...
Hi,
I'm looking at using the NRF9160 in a system where every microamp counts. The NRF9160 already includes a DC/DC converter, but as I understand it is step down only...
Working on an application that can be compiled with BLE functionality turned on or off, I found my "BLE off" configuration failed to compile with the following error while...
Hello -
I am trying to print a 64-bit unsigned integer (uint64_t) to a CLI output. I've based this on the CLI examples in SDK 17.0.2. Specifically this is the function I...
refer to: http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multi_image.html developer.nordicsemi.com/.../partition_manager.html
Where I change those image...
My accelerometer readings appear in my segger embedded studio "Debug Terminal" window.
It looks like this.
I want to stream the data via COM port to this "serial oscilloscope...
