Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
How do you use the nrfx_temp driver in a project? I'm on SDK 17.0.2, segger, and an NRF52840-DK board. I see the old HAL temp sensor is deprecated and it seems to always return...
Hi,
I have been using a certain 16MHz oscillator up until now without any issues, and now wish to replace it for logistical reasons, what kind of testing are recommended...
I'm designing a product which incorporates a magnetic sensor (MMC5633) and a Bluetooth microcontroller (NRF52832). The sensor and bluetooth chip share the same ground plane...
hi,
We have some products that have been sold out(hardware:52832,software:sdk13,softdevice:s132_4.0.3).I want to upgrade their sdk to 15.3 through DFU.I learned in the official...
Hello,
I'm trying to modify the current ASSET_TRACKER of SDK v1.4.1 to get it to work in my own server on AWS-IoT.
I'm wondering if there is any documentation about this...
use SDK17.
central uses nRF52832 and peripheral uses nRF52810.
I want to implement the exchange of data with each other.
First, the central scanned and connected.
...
While using NRF52840 SDK with twi_scanner i am able to see i2c address 0x68, but while using zephyr unable to get the data.
I have seen I can configure i2c pins in board...
As I'm new to the BLE, I'm trying to make use of examples enclosed in the nRF5 SDK.
Now, I found that there exist several functions that seem like do similar things and...
1.4.8 programmer is complaining 'Error while getting readback protection' when connecting to the BL651, 453-00005.
Used to work.
Seems to connect OK to BL652-SA-01.
Hi,
We have a product using NRF52840 ready for production. In factory production environment we want to validate the product for PCB, product assembly etc failures and also...
Hi,
I am going to implement a PPI to connect GPIOTE event in with TIMER COUNT TASK, and then read the count from CC[0]. But the count in CC[0] never updated.
Basically...
Can I get suggestions on how to implement the following topology with respect to provisioning:
There are a series of lights and each of them is connected to a central...
I want to write a data stream coming over UART into flash memory of the nrf52840 & echo it back after writing it to flash .
Please suggest from where i can start ?
Thanks...
Hi,
I was trying to create bond between my Android app and the device. At the beginning it worked well, and later I erased the board to start over. But then my app would...
I'm migrating an existing application from SDK v13 to SDK v15 and have run into a minor issue with the fstorage changes introduced in SDK v14.
My application uses both fds...
