Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Back in SDK 17 or so there were code samples for both the client and server side of the LED button service.
What happened to the client/central example when you migrated...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
I'm developing software for the nRF5340 based on the NCS 3.2.4 "hello world" example. Adding bt_enable() returns error code -11. Please tell me how to implement bt_enable...
Hey all,
I've been working on a family of commercially available cellular IoT devices using the LwM2M protocol utilizing nRF9160 and nRF9151 SoCs. In the European Union...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
Was excited to get an (apparently) early copy of the nRF54LM20B-DK so that I could explore all the Edge AI capabilities of the system (using both Neuton and Axon models)....
I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
I am testing the NRF9151-SMA-DK NTN function using the mfw_nrf9151-ntn_1.0.0 firmware and serial_modem_v2.0.0-preview1_nrf9151dk_normal_mtrace app. I keep seeing
%MDMEV...
HI,
I'm reading this post about NFC antenna matching. It says in Method 1 to connect the coil antenna to the S11 port of the network analyzer. How should I make the connection...
I am currently working on a design with the nRF9160, and have a few questions about the DEC0 pin and decoupling for the module in general. I have been considering adding additional...
I keep seeing this in your documentation:
This functionality is in the process of being deprecated and replaced by Zephyr’s default devicetree-based memory partitioning...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hello Nordic Team,
I am evaluating the nRF54LM20B physical DK using nRF Connect SDK v3.3.0‑preview2 . In the SDK, only the nrf54lm20apdk board target is available, and BLE...
Hello, I am working with the following sample project and NRF Connect SDK v3.3.0. (Referenced regarding this topic .) The sample implements DFU with MCUBoot while using the...
I am evaluating the output power of a testboard that uses the nRF52840-QFAA.
The matching network closely resembles the recommended network in the datasheet (shown in figure...
