I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Good morning,
In order to save some user data in flash, I want to fix page size to 32 bytes. It will be more useful for me, and it will be easier according to my project...
I've been playing around with the UART drivers on SDK 15.2. No issues with the Legacy (w/DMA) however I've tried switching over the NRFX_UARTE driver and I can't get the driver...
Hi,
Our device is based on nRF52840 SDK 15.0.0
The device verifies signature of incoming messages (which were sent over BLE from PC application) using ECDSA with spec256r1...
Hey guys. I am making a firmware using nrf52840 dongle which scans nearby bluetooth devices. I do not want to connect to any device, just send scanning data to another device...
Hi Because I have a custom board with the nRF91 module, there is no possibility to send data to nRF cloud, because it works only with DK boards. I would like to send asset...
I want to use this sample application, to connect with nRF52832 DK loaded with Running Speed and Cadence Application. In other words I want to use nRF9160 as a gateway for...
Hello all,
my compiler can't find the definition to timer functions : nrf_drv_timer_init(), nrf_drv_timer_extended_compare() and nrf_drv_timer_enable(). bellow my code :...
I am using Nordic nRF52832 Development kit . I want to interface Load Cell with the Development kit. Which examples in SDK i should refer to get started with Load Measurement...
Hello ,
i am facing some issues regarding nrf mesh uart example.i am using nrf52 sdk and trying to use uart for my project to send a data to a particular node in a group...
Hello All,
I am trying to merge the "secure_bootloader_s132" and "ble_proximity" examples.
I have combined all file .
(Here i am using Segger embedded studio with nRF52...
Based on the mesh sdk3.1 operation dfu, according to the operation instructions, dfu_mesh.zip cannot be generated.
nrfutil dfu genpkg --hlep Found no parameters for mesh...
Hello everyone,
A nRF52832 with SDK 15.0 was used for my application. I am trying to send a large amount of data via BLE with a custom BLE service. I extended MTU size so...
Hi
I have been developing a 'custom' firmware to be used in a nrf52 based device. The idea is to replace the original firmaware (too limited) and burn my own.
Hence, I...
FYI,
the auto-update fails for version 2.7.0 of 'nRF Connect for Desktop’ with the attached error dialog.
I had to manually download it again from the link below, and...
When I am trying to run my code in nrf52840 DK board, the program halts in a specific PC and does not go forward (2nd image).
I am using SDK version 14.0.0 and softdevice...
