Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I'm writing a production script that uses nrfutil to do OTA DFU for both nRF51 and nRF52 radios. I'm using a PCA10059 with nrfutil version 3.5.1.
It works fine for an nRF52...
Hello,
I am trying to use IAR examples to debug some of the examples provided in the SDK.
I am only using examples that support the pca10059 dongle.
One example is the...
Dear All and @rogerclark,
From the release note of nRF5 SDK v14.1.0, Segger Embedded Studio (SES 3.30) IDE has been supported originally.
I use MacOS, and I has set...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
I am currently looking at how to put the nrf52 development board to sleep (and wake up) by sending a command from an android application (with SDK v15.2).
I have been experimenting...
Hi
I am trying to establish communication between a NRF24L01+ and an NRF51822, but unable to do so. I am able to communicate between 2 NRF24L01 + and also between 2 NRF51822...
Hello, I'm quite new to both the nRF52832 and the Segger Embedded Studio. I have a college project which involves I2C communication with 2 slaves. I was finally able to set...
Hello,
I am trying to read data from a sensor through sensor TX pin connected to RX pin of nrf51822. Nrf51822 recieves this data through RX pin and sends it via bluetooth...
I am seeing a problem using the nRF52 SAADC with two analog channels enabled in scan mode.
Essentially, channel 0 is measuring an analog signal with gain ~= 15 while channel...
Hello,
I am trying to get the RX interrupt to trigger on the PCA10001 board using the segger debugger as my serial terminal.
My hardware setup consists of a PCA10001...
SDK: v15 SoftDevice: S132 Chip: nRF52832 on BL652 Module
I have a command->response type system. The Central (Android phone) sends a command, and the Peripheral (nRF52 device...
Greetings!
I am using nRF52, SDK14.2, and NUS with MTU = 64. I want to transmit 1000 byte string over BLE upon reception of any character to "nus_data_handler" I have divided...
Hello. I'm just trying to get going with the nRF9160 DK which just arrived.
Using macOS.
Followed Getting Started and then nRF Connect Getting Started Assistant, and everything...
