hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi
I am using the SDK 15.2.0 and developing for a NRF52832 using Segger.
I have a problem with the define NRF_SAADC_CHANNEL_COUNT in "nrf_saadc.h". It is set to 8. ...
Based on Mesh SDK 2.1.1.
I use light switch proxy client & proxy server to test server publish function.
But when I use the phone setting network, I found that the client...
Dear nordic,
we build a custom board with nrf52840. Now i face some issue i can't flash the board. when i start flashing its show some warning reset pin is high.
I...
Hi,
I just want to verify-
The MAC address of the bootloader is the app MAC address +1, assuming we are using the default configuration.
Is that correct?
Thanks, ...
Hi Support team,
The Online Power Profiler is calculating the Average Current consumption for nRF52840 DK board in a wrong way.
Calculation is of blocks. => Pre-processing...
Hello
I would like to integrate DFU into my application
but, when including:
#ifdef BLE_DFU_APP_SUPPORT #include "ble_dfu.h" #include "dfu_app_handler.h" #endif...
Dear NRF Team:
I successfully updated the firmware (blinky_nrf52840_xxAA_s140_6.1.0) according to the Mesh DFU steps.
However, the second DFU cannot be performed after...
I am experiencing an issue where the program hangs on one board, but not another. I am able to program the Evaluation board (EV BT832AF) ok and run everything, but when I...
Hello,
I was wondering if it is possible to change some of the BLE Stack Configurations based on the number of devices connected...
e.g. Changing Connection Interval and...
Hi,
I am evaluating the Firmware on this github repo and my nrf52832.
At the moment I am compiling it using my makefile, however I would like to import this project...
Hi All.
We have flashed the hex-file of ble_app_blinky for pca10040 on the debugger, and things work fine.
We are using sdk-15.2 with softdevice-6.1.1
So, a question...
Hi there, I am having issues knowing how to get access to data coming through a VisualGDB embedded (C) project using the pc-ble-driver. I have my project working fine and...
Hi ,
Nrf52840.SDK15.2,Windows,Ses
Compile "secure_bootloader_usb_mbr_pca10056_debug " project, An error occurred. As follow：
Cannot open file: E:/new/project/wireless...
I have used the UART example up and got it working. So i can send and receive data using it.
However i wanted to modify it so as to run with the current RTOS environment...
Hello
According to BLE Specifications we should be able to get 125kbits/s over the air transmission i cannot seem to get anything remotely close to this.
Is there something...
