Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi All,
Hoping this is straightforward for an intermediate developer.
nRF52840-DK (matched dongle not yet in use), SDK 15.2.0, SES 4.10a (Jlink 6.40), Windows 10.
My...
Hello,
I have seen that the nRF52840 PS v1.0 specifies the RSSI_PERIOD to be 15us. I have also seen that the nRF52832 has only a RSSI_PERIOD of 0.25us (PS v1.3+) or 8us...
I need some technical information:
- the micro Host can (through a pin?) make WakeUp of the BLE module to configure it / change the operating parameters etc? - the BLE module...
While visiting the Nordic Tech Tour we were discussing the pros and cons of BLE Mesh with a Nordic employee. He recommended that we also looked at a different solution, a...
This is essentially a repeat of :
https://devzone.nordicsemi.com/f/nordic-q-a/38808/is-a-3-bit-synchronous-3-data-lines-clock-parallel-input-at-16-368-mhz-feasible
Instead...
Hi,
I am using Keiluvision 5 , nRF5-SDK version - 15.2 with SoftDevice S140, My application requires to have NFC functionality as well as UART, but when I try to merge the...
Hi. need help with dynamic routing. I have a 9 node mesh running Thread and so far i have collected and analyzed latency data and packet delivery ratio data. I need to find...
Hello there,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hi Nordic,
I plan to use the newest SDK (because the ATT MTU > 23 is need) for NRF52832 to develop a PC tool to connect with Nordic BLE peripheral devices, and then send...
Hi, i am using SDK15.0.0 with nrf52840 chip.
I am interfacing a SPI device in the SPIM0. The SPIM module looks working fine without a softdevice.
But when i integrate...
SDK - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Hi,
I am using an android phone to write a 32 byte array to the nrf52 device which...
nRF51_SDK_10.0.0\examples\ant\ant_plus\ant_bsc\bsc_tx\combined\button\pca10028
ANT BSC Speed event time not change After a period of work although button press or relea...
Hi. I am a beginner with nrf52832. Trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
I have problem with both custom boards and DEV board.
From a certain time after GPIO direction bit seems not effecting the pins.
To get rid of software factor, I all erase...
Hello,
I'm currently using nrf8001 to sent a 20-byte packet. It works fine and my phone application receives the right data. However, when I send another packet that has...
