Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Good morning/afternoon/evening,
So I am fairly new to nRF system and wanted to know if there is a way to execute an interrupt when one of the buttons on the board is pressed...
Hi, I have a custom board built around a nRF9160. All GPIO (P0.xx) work. However, when I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the...
Hi,
We are evaluating the possibility to connect our nRF52840 to another BLE device but we are facing issues with UUID Nordic handling strategy.
Quickly:
We have...
Hello,
I applied for a SUPL license for two weeks, but was denied.
I repeated logout/login, but it was the same.
please help and check.
Thanks,
SY Kang.
Hi,
as follow is nRF5 SDK code to create a timer ms.
how to create a timer ms on nRF Connect SDK ?
APP_TIMER_DEF(m_timer_speed_1ms); int timer_lms=0;
static void...
Hi,
we have an odd issue on ~ 50% of our in-house boards here. We're using the internal RC as a low frequency clock, and then enable one RTC. No softdevice or anything....
i am using nrf52840 USB dongle and the segger J_LINK EDU mini for debugging when i use bulid and run it works, and if i remove the donle and reinsert it then ts not working...
Hi,
I was using nRF command line tools 10.14.0 before. i try to update to 10.15.1 but fail with below log.
Do you have any comment for us to overcome this issue? ...
Using NRF Connect for Desktop V3.9.1 for Windows. We flash custom boards with J Link EDU 9.4 version. Since update to Programmer v2.0.1 it will not detect the J Link. Any...
Hi,
ncs1.8.0\zephyr\samples\bluetooth\periodic_adv\
ncs1.8.0\zephyr\samples\bluetooth\periodic_sync\
periodic_adv and periodic_sync
how to change to use Zephyr controller...
Hi,
I have a nRF5340 with USB DFU support which uses MCUBoot for upgrades. The current build (app_version_1) on the nRF has 0x4000 as the size of the settings_storage. The...
Hi,
Developing by NCS SDK, We found it will take 20 minutes by using mcumgr(on MacBook-pro) to BLE OTA 178KB image to nRF52840 Product Board's external SPI FLASH. it success...
The following is my set up:
platform: windows 11,
editor: visual studio code with nRF connect
SDK: nRF connect SDK v1.8.0
toolchain: nRF connect SDK v1.8.0 toolchain...
Hi,
Here is my hardware.
VBAT is 3.6-4.2V, UWB_EN is Pin28.By using nrf_gpio_cfg_output( UWB_EN ) to init this IO.
Is there any problem?Because when I using nrf_gpio_pin_clear...
