Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
Hi,
I am doing some research for the antenna matching of the NRF52832. Now the product specification v1.4 on page 551 states:
"A matching network is needed between the...
How to make the nRF52840 SPI work in 8M with 1.8V supply?
We test the PCA10056 nRF52840 DK board, and find the 8M SPI CLK&DATA wave is very bad. The 8M SPI works fail with...
hi
I tried zigbee tx carrier mode start at 11 channel and tx power = NRF_RADIO_TXPOWER_POS8DBM.
But, When measured with measuring equipment, i got zb tx power -20 ~...
I recived nrf5 SDK V17.0.2
I'm testing with in "nRF5_SDK_17.0.2_d674dde\examples\peripheral\radio_test" folder.
I tried zigbee tx carrier mode start at 11 channel and...
The application I am designing gets a pulse ox measurement from the user, sends it, disconnects, and shuts off. Are there any deleterious side effects of exiting the main...
Is it possible to fill some field when sending advertise message.
We want to change some filed periodicity, so is it possible every time sending the advertise message. ...
Hi,
I still have issue with programming.
I don't understand why i always have trouble with DLL.
I'm able to program with SES, the bootloader and my application. But...
I have a BMD-300 Eval board with the nRF52832 programmed as SPI slave using the SPIS example program. It works, but I cannot figure out how to send a message back to the master...
Hi,
I have done some reverse eng on a nrf24l01+ emitters using spi spy and managed to catch datas using an arduino leonardo + nrf24l01+ using the following register setup...
Hi All,
I have an nrf52833DK and now I want to debug the program.
I am using NCS V1.4.99 and using SES for development. I created a 52833 project, but I used the nrf...
Hello,
I am trying to implement the IAS Zone on a nRF52840DK, with reference to the CLI agent example.
How do I get the IASZone.h and zcl_option.h file?
Where do I include...
We want to physically connect our nRF muRata dk (WSM-BL241-ADA-008DK) to the ST Accelerometer eval board (STEVAL-MKI197V1). We are assuming the connection takes place on the...
I want to used p1.01 and p1.2 and p0.13,so how to defined it.
I do like
#define led0 13 to used pin p0.13 its working but how to define pin P1.01 and all
Hi,
I'm using nrf52840 and connecting to a mobile device.
Randomly - I get disconnections with error code 133 - on characteristics write, on mobile side.
In addition...
thingy91:nRF52840 int64_t convert the value to string in sprintf
Add next line in proj.conf
CONFIG_NEWLIB_LIBC=y CONFIG_NEWLIB_LIBC_NANO=n
If you do the following: ...
