Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi all,
i just received 2 nRF54L15-DK boards. Both I am not able do program - I tried:
1. nRF Connect for Desktop
* I did not make any change on the board afre unpacking...
I want to use the boards NRF-5340DK or NRF-52840 with the external host for the channel sounding feature. Can we use the feature on the mentioned board? If so, can you please...
I'm trying to send and receive an extended advertisement packet with about 100bytes of payload.
I started with the sample extended_adv example.
I 1st validated that using...
Hello. We are updating firmware to use nrf sdk 2.9.1 (from 2.5.2). Below is my proj.conf, should I expect any breaking changes?
############################
# Stacks...
Hi,
I want to configure the nRF9160's internal flash storage_partition, it has 32KB currently, I want to change it to 100KB. How to do that? Using nrf9160dk_nrf9160_ns.overlay...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
Toolchain v2.70, SDK v2.6.1, VS Code, Windows
Code derived from UDP sample works on DK board but fails on custom device.
Device is using DK board configuration, but no...
I have used ADC Channel 6 (P0.30) for voltage measurement using NRF52832. Previously It was working well. Now it is returning an error.
00> [00:00:00.398,345] <err> adc_nrfx_saadc...
Hi
I have been working on a project for some time, using the SDK and the nRF Connect for VS Code plugin. A few weeks ago I stepped away from this to take on different work...
Trying to find some docs on "flashing" vs. booting the nRF54L15 from RRAM.
- are there any implementations available? - any ways to lock 1st & 2nd-stage bootloader areas...
hi
I am using version ncs 2.9.0 and I use mcuboot for DFU. How can I modify the name of the final generated `merged.hex` file? I tried adding this to the `.overlay` file...
Hello. I am working through the tutorial Azure IoT Hub trying to connect our board to an Azure IoT Hub using DPS. Things seem to work up until the point where our board actually...
Hello,
I want to get the software for nrf5340 audio dk running on a custom board hardware. For that I created a custom board with the VS code plugin. For the beginning I...
Dear Nordic support,
We are experiencing a throughput issue with an nRF52840 dongle operating in the central role, running a custom application developed using nRF Connect...
I have looked at the Altium Designer files for the following examples:
nRF5340-CLAA Reference (nrf5340_claa_config2)
nRF5340 Development Kit - Hardware files 2_0_0 ...
