GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I am using the nrf52833 dk board with vs code , I have tried all the solutions that I could find on the already available asked questions, example https://devzone.nordicsemi...
SDK: nRF5 SDK v17.0.2
use example SDK17\examples\ble_peripheral\ble_app_uart to add DFU over BLE
SoftDevice: ANT_s332_nrf52_7.0.1.hex
MCU: nRF 52832
windows application...
Hello, guys.
I just wondered why use LTE Link monitor from nRF Connect make nRF9160 scan lte-m networks and even connects to it.
And when I'm trying to use external MCU...
Hello,
We are using this module in our new product and are in the process of Bluetooth certification. The BMD-350-a-r lists QDID of 101018, but the nRF52 family lists...
Hi,
We are using nrf5340 and nrf connect SDK V2.0.0
Using below code, we are able to scale up/down the processor frequency.
However, in our application we want to...
Hello,
I want to specific a hci event in zephyr RTOS when using nrf connect sdk. But I don't know how to achieve it.
In Bluetooth Core v5.2, vendor specific events have...
Hello,
I would like to create my beacon application to publish periodically (e.g. 10sec) data related to three temperature sensor.
What're the possible solution to implement...
Hi Team,
I am using nRF5340 dev kit and NCS(Nordic connect SDK 2.0.2)for my DFU POC purpose. I want to perform DFU update of nRF5340 through nRF USB port instead of the...
Hi developers,
Now, I want to get a correct Tx power value. I printed out the value from "ble_gap_evt_t->params.adv_report.tx_power" and could get only 127, even this...
Hi,
I am using 5340 but it's uart consumes a lot of power 2.01mA
SDK: NCS2.1.0
project: peripheral_uart
I have disabled all other peripheral equipment,put all...
when I open nrf connect for desktop i got blank page,
and there nothing in the console:
I've installed/am using:
nRF Connect for Desktop v.3.11.1
J-Link V7.68b...
Hello,
we are using the nrf9160 in one of our products. Our assembler has used old nrf9160 SICA B0 chips on our first protoyping round. When we run our software on the nrf9160...
Hello, Guys.
I had problem that if I config nRF9160 through UART0 (default) it works and I receive IP address and can make MQTT connections.
But when I use UART2 (external...
Background:
I seek to interact (human and/or additional MCU) with both UART peripherals (uart0 & uart1) in the easiest manner possible - issue commands, pass traffic, etc...
I have shell working with the following configuration
CONFIG_SHELL =y
CONFIG_SHELL_BACKENDS =y
CONFIG_SHELL_BACKEND_SERIAL =y #also selects serial
CONFIG_SHELL_CMDS...
