I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hi everyone,
I am making a zigbee mesh with just coordinator and routers only. I intended to have the mesh to cover a very large areas with nodes that can be moved (not...
Hi,
I have got some problem of understanding the IQ sampling data.
As below is the official data format
0: I_Q (default)
Q
31:16
12 bits signed, sign extended...
I have successfully installed the drivers and downloaded the latest firmware version, but the connexion fails and I can not use the AT interfaces command for the modem controller...
Hi
I am using an example project written for pca_10040, I am trying to replace it with pca_10010.
So far, I changed the "Target Device" in the project options and the...
Hi all,
Currently we are trying to measure the power of nRF52832 using (1) nRF52 DK board, (2) power profiler kit 2 (PPK2).
We used PPK2 in source-meter mode and we connected...
Shalom!
I have a custom nRF9160 board with uart0 connected to the outside world by RS232. I set the uart0 as the printk() debug output. I also need to write and read binary...
I get that is has to do with something around the MSB. But I cant seem to find a way to prevent this. No i can not send a byte 0x00 since this will trigger certaint behavior...
Hi,
I am developing an Openthread application using Nordic Connect SDK for the nrf52840dongle. I updated my nrf SDK to bd075cc09. Since then, my application won't boot anymore...
Hi,
I need to switch DK to 3v as my custom board has 3v.
When I switch VDD_IO to 3v board doesn't start at all. LED5 blinks for a moment but nothing happens.
Switching...
Hi,
I am currently working on an internal dfu modeled after the secure_bootloader_uart/ example in SDK 15.3.0. I have gotten the dfu to perform a successful dfu with the...
Hi!
I am developing on a custom board and only have the Debug in connector P3 from nrf9160dk to debug the board. I want to send AT commands to configure the modem and will...
I am a systems engineer helping my team in the component selection phase of the project that involves BLE communication between our master side and a simple remote control...
I have issue to program nrf52832 with nrfjprog command line.
my program use nrf52formesh sdk. I developed with Segger Embedded Studio with GCC on the Linux PC. I modified...
Hello all,
I have successfully installed nRF Connect, nRF Connect SDK v1.6.0 and SEGGER Embedded Studio (SES) v5.50.c to run and debug some samples on my nRF5340 Development...
