Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
hi,
i am using working on example "pin_change_int" in peripheral folder.in this example interrupt occurs when there is state change on interrupt pin. how to enable interrupt...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
Hi,
I want to identify the specific provisioned node among all n number of provisioned nodes using nRFMesh app.
Does any event will be appeared in sdk, after provisioned...
Hi, I am begginer, I work with SES, Mesh_v5.0.0, nRF5_SDK_17.0.2, and s132, SD v7.2.0. I started it two weaks ago. :)
I tryed the examples, Light switch , with server and...
Does Nordic have an example SW for transmitting and receiving data in BLE 5.2 connectionless isochronous communication mode? Is there a SoftDevice that would support this...
Hi, good morning , i am just wondering is it possible to send and recive data through ble faster than the coded examples please as i am sending gyrodata and its taking about...
Hello - I've google'd around a bit on this unsuccessfully...
I've successfully provisioned and configured an nRF Mesh network with mutliple servers and a single client,...
hi, I am working on the nrf52832 device, I have implemented the push button and I am able to detect button push and release but I want to notify the app when the push button...
Hi,
I am trying to interface nrf52832 with LoRa transceiver module sx1262. Can anyone please provide some sample code to check basic Tx/Rx of this chip. I am unable to find...
Hi,
I am looking for an example that uses the eDMA with the TWI in the 15.2 SDK on nRF52840.
My idea is to read out an external sensor using the TWI with as little processor...
