Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello everyone,
We're looking to develop a prototype of a very simple panic button. The device should automatically pair with iOS / Android, and establish a call to a given...
I have an example application executing on the nRF52840-DK on SDK15.0.0, see https://devzone.nordicsemi.com/f/nordic-q-a/67351/are-there-any-differences-between-sdk15-and...
When we try and stream BLE data to the nRF Connect app on an Android or IOS phone the app accepts our requested for an MTU of 244 or 160 respectively, however it does not...
Hi,
Dev setup:
Segger embedded studio - fatfs example - SD card - nrf52832
I am able to write to sd card and see data. But while reading i am failing.
Below is code...
Hi,
I am a bit confused after looking through all the SDK solutions available for NRF52 and need a piece of advice...
I am have started on the project that consists...
Can I periodically or continuously read the characteristic of peripheral after the connection?
If there is a change in the value in peripheral, then the value is received...
Hi,
i am trying to do buttonless dfu . I want to merge all hex files into one as per the document .when i enter the mergehex , i am getting mergehex command not found why...
Hi,
I'm making an new board with both nrF52840 and nRF9160. In addition to the radio ICs there will be some antenna diversity switches, chip antennas etc.
So I'd like...
Hi,
I'm using SDK 15.2 with Nrf52832,
I've implemented a custom service with read, write and notification services.
I would appreciate if you could send me an example...
Hi,
I have a problem with the NRF52840 DK rev. 2.0.1 coin cell. When powered via USB board is working properly but when powered with coin cell nothing happens.
SW08 is...
I bought a development board nRF52840. Connecting it to the PC (WIN 10 x64) will not recognize the device. At first I thought it could be the cable, bought a couple and it...
Hi Team,
One of our requirement is to measure the crypto functionalities timing like how much time it is taking for digital signature signing and verification. Is there...
I wanted to know if there any any static analyzers that work well with the nRF5 SDK.
I was thinking about adding a static analysis (e.g pc-lint) check to our code base and...
1. When I loaded the 9160 project, I had problems,
arm-none-eabi-gcc.exe:error:CreateProcess
9160 development environment, the required software, I have installed...
1. When I loaded the 9160 project, I had problems,
arm-none-eabi-gcc.exe:error:CreateProcess
9160 development environment, the required software, I have installed...
