Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Dear nordic,
we build a custom board with nrf52840. Now i face some issue i can't flash the board. when i start flashing its show some warning reset pin is high.
I...
Hi,
I just want to verify-
The MAC address of the bootloader is the app MAC address +1, assuming we are using the default configuration.
Is that correct?
Thanks, ...
Hi Support team,
The Online Power Profiler is calculating the Average Current consumption for nRF52840 DK board in a wrong way.
Calculation is of blocks. => Pre-processing...
Hello
I would like to integrate DFU into my application
but, when including:
#ifdef BLE_DFU_APP_SUPPORT #include "ble_dfu.h" #include "dfu_app_handler.h" #endif...
Dear NRF Team:
I successfully updated the firmware (blinky_nrf52840_xxAA_s140_6.1.0) according to the Mesh DFU steps.
However, the second DFU cannot be performed after...
I am experiencing an issue where the program hangs on one board, but not another. I am able to program the Evaluation board (EV BT832AF) ok and run everything, but when I...
Hello,
I was wondering if it is possible to change some of the BLE Stack Configurations based on the number of devices connected...
e.g. Changing Connection Interval and...
Hi,
I am evaluating the Firmware on this github repo and my nrf52832.
At the moment I am compiling it using my makefile, however I would like to import this project...
Hi All.
We have flashed the hex-file of ble_app_blinky for pca10040 on the debugger, and things work fine.
We are using sdk-15.2 with softdevice-6.1.1
So, a question...
Hi there, I am having issues knowing how to get access to data coming through a VisualGDB embedded (C) project using the pc-ble-driver. I have my project working fine and...
Hi ,
Nrf52840.SDK15.2,Windows,Ses
Compile "secure_bootloader_usb_mbr_pca10056_debug " project, An error occurred. As follow：
Cannot open file: E:/new/project/wireless...
I have used the UART example up and got it working. So i can send and receive data using it.
However i wanted to modify it so as to run with the current RTOS environment...
Hello
According to BLE Specifications we should be able to get 125kbits/s over the air transmission i cannot seem to get anything remotely close to this.
Is there something...
I use Multilink and Blinky Demo with PCA10056 and PCA 10040 Board,when the two board close to each other there is no packet loss,but when i dispath each other with 50cm,there...
Hi,
I am currently using two different programmers(nrf51DK, Segger flasher portable plus), programming software's ( NRFgo Studio, Jflash). Here are my issues:
When I...
