I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hi,
Function call to > err_code = ble_advdata_set(&advdata, NULL);
returns always err_code = 7 (NRF_ERROR_INVALID_PARAMETER) for a 128 bit UUID type (BLE_UUID_TYPE_VENDOR_BEGIN...
I am using pca10001, SDK6, SD7.1.
In my application i want to send a large amount of data to central(ios).
So im sending data as a packet of 19 bytes and each packet with...
I have NRF 51 DK.
I adjusted the toolchain path to arm-gcc 4.9 2015q1. This version works fine for the NRF 51 SDK.
I get this error:
lto1.exe: fatal error: bytecode...
I'm seeing the resetreas show the CPU lock-up detected after I reboot. This error is occurring while using the ADC. What type of fault condition can cause a CPU lock-up detection...
Hey everyone,
I'm developing an application using the IoT SDK . The first part of the application consisted of a normal BLE peripheral to interact with an android app....
app_timer.h contains a useful macro for getting from milliseconds to a number of timer ticks, given a prescaler value with which the timer was started:
#define APP_TIMER_TICKS...
Hello,
May i know what will happen if we happen to assign the same pipe address for let's say pipe 1 and pipe 2?
Can we still receive data and be informed of the pipe...
Hi,
My goal is to send temperature values on the advertising so, I'm trying to get work this example, but i have an error about this lines of the code on keil:
advdata...
Hello, how can i modify the hrs_s_evt_handler() to initiate bonding only if it my configured belt address?
My Solution:
static void hrs_c_evt_handler(ble_hrs_c_t * p_hrs_c...
Hello, All.
I want to know AppID in iPhone's App using ANCS.
(for example, Facebook App's AppID is "com.facebook.Facebook",
Facetime's AppID is "com.apple.facetime")...
Hi Nordics!
I want to add custom service into ANCS example for android.
But I cannot understand how to add custom service stably.
First, I just added my custom service...
I have compiled the nRF51-ble-bcast-mesh 's examples: "LED_mesh_SDK7" and "BLE_Gateway_SDK7" on Keil uVision v5.14.0.0. But, I am facing problems flashing them on to my nRF51422...
I have a problem that I can't figure out. I have a custom board with an nRF51822 QFAB. The board will run a test application that uses nrf_delay_ms() to toggle an output pin...
Hi!
I have reviewed the NRF518 reference design, i.e., case "PCB layout recommendations for the NRF51822 WLCSP62 package" and the layout pdf files provided therein:
...
