Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
Today I use the app timer to start a simple 8bit ADC conversion each second and send in the irq handler.
Now I am trying to use the sw interrupt to execute some...
Hi
I want a 1K Hz square waveform to drive a peripheral device, but I can not get a continuously square waveform on GPIO 19, pls have a look at the picture I attached,...
Hi All
I am facing one issue using app_timer.c, When I put the PRESCALER value as 327 and started timer as app_timer_start(timer_ID, 100, NULL);, It was giving only 920ms...
Hi,
I ran the Nordic nrftoolbox on Sony Z1 android 4.3. I found that the device name is not showing on the list as attached. Running the Nordic nrftoolbox on Samsung S4...
Hi there,
We are using the nrf8001 and a arduino to read out two sensors.
The two measurements should be at the same time and therefore are coupled to eachother.
Is there...
Hi
I try to program my custom board using J-flash and Flasher ARM ( for production ).
Attached my J-flash configuration.
Connection with device is successful established...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I tried the booloader program on nrfgo mother board and it works as it is.
However, after I followed the same procedure and download to our inhouse board which is...
Hi!
I'm trying to receive notification on a characteristic that I've written before but I can't. I've activated the Notification in that characteristic, after that I write...
This question is somewhat related to: devzone.nordicsemi.com/.../how-to-switch-between-over-the-air-and-uart-bootloader-mode
I know it is possible to switch between HCI...
Hi
I'm working on the DFU feature according to the "device_firmware_updates" example on PCA1001 board, basically it works, but the question I'm facing is the board always...
hello,
We used the nRF51822-BK-FW 1.0.1
We need a little more help here to add the MAC address to the advertising packet. Can Any one help us add that to there?
i m attaching...
Hi,
Could anyone give some idea how to do data transfer with help of L2CAP (calling L2CAP APIs from Application)? I will be very much thankful if give description/steps in...
Hey all,
I have a custom board running a 51822 rev C0 chip connected to a TMP102 temp sensor over I2C. I was using the twi_sw_master.c to successfully talk to it in my...
