I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Good morning,
We have a new equipment based on the nRF52840 and s140.
Just now, a new problem has appeared and it is very strange, as it seems to be a ‘random’ error:...
Hello,
I am currently using Fanstel dongle, where I am trying to trigger the USB DFU with nrf connect programmer (buttonless). The example which is provided works on the...
Hello,
I am using an nrf5340dk and I am trying to create a qdec sample using as reference the wheel module.
I have added set the CONFIG_SENSOR and CONFIG_QDEC_NRFX to...
Hello Nordic Experts,
Recently, I have been investigating the radio timing for advertising, I tried to find answers online, but I failed. To explain more clearly, let...
nrfutil is required to program the nrf52840 dongles being distributed at the 2022 Zephyr Developer Summit. west is the tool used by zephyr to install, build, flash, etc. ...
Hi,
I have a QSPI flash device with a weird bug (I think). Basically, when the RDSR command is executed, the HOLD pin needs to be held high otherwise the flash chip status...
Hi,
I'm developing with Segger and nRF52832.
I'm writing a code that makes two tasks into RTOS and sends data to BLE after I2C communication and SPI communication respectively...
Hi, I am using NRF5340 and I want to connect it with a 128x64 oled display with the I2C protocol (Scl, Sda, Vcc, Gnd), I have been trying to connect it for more than a week...
I want to interface 4 Digit Seven Segment display to nRF52840 Dongle and display the data(number) , which is received by it through Mesh protocol. I have successfully implemented...
Hi, I'm running a DFU ble_app_buttonless_dfu on nRF52833. Unfornately, my board is not supported it use pca10100. SDK 16 only supports pca10056 and 10040. I have used pca10056...
I have nRF52832 with factory reseted FW.
I need to make 52832 enter bootloader mode without pressing button. By just RPI4 PIN control program.
Planning PIN connection...
Hello Community!
I have an nRF52840 DK and the Segger Embedded Studio. I have Open nRF Connect SDK Project... and chosen serial_lte_modem. I build the solution modifying...
New design and I have a weird behaviour on the low voltage output of the internal LDO for CPU .
I have monitored DEC1 voltage on scope
Thats all the supply pins...
i am working with s140 on nRF-52840 and i send the data with sd_ble_gatts_hvx() and notification on custom service but the length of transmitted data always = 501 even if...
I'm attempting to check out the bootloader under the nRF Connect SDK 2.0.0. This is critical for us to be able to move off of nRF5. I am starting with the smp_srv sample,...
