hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi
I'm trying to create a central device to connect with a series of different peripheral devices. All the peripheral devices can be discovered during the scanning. However...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hi,
I have previously compiled the zigbee command_line_agent for the PCA10059 which I use for testing.
It worked when uploaded so I have one working PCA10059.
Recently...
Hi,
I have a problem getting interrupts by the rtc component working. I am using the nrf58211 chip, nRF Connect SDK v. 1.9, uBlox BMD360-eval development board.
My code...
I have Windows 7 pc on which PCA10040 DK is used to test UUT.
- Devkit frequently gets corrupted for unknown reason.
-It has custom Firmware which is validated to be working...
I learned today that the ALIGN_NUM macro doesn't work as expected if the data type passed is not unsigned int type. I find that using int32_t or uint8_t with ALIGN_NUM produces...
I'm using nRF Connect for Mobile on my Android smartphone (HTC U11, Android 9) for over a year now
It was working well so far last year, then I paused for a few weeks and...
Is a bootloader required to flash code to the nRF-52832?
I built a custom board with a blank nRF52832-QFAB-R. I'm able to run through the tests on the Segger J-Flash V7...
Hi
I am working with an nRF52DK board that is successfully communicating with Nordic's nRF Toolbox app via BLE UART.
I would like to be able to modify the app as I modify...
We need to read/write to an I2C device that uses a 16-bit register addresses (Melexis MLX90632), and the nrf_drv_twi_tx() and nrf_drv_twi_rf() functions seem to be limited...
Hi,
We would like to impelement Pairing and security features in our device. Our device will act as server in peripheral mode. The cleint device should ask for 1 passkey...
Hi Nordic,
I'm referring to this doc but still not quite clear about how to enable the chip for BLE RF HW validation.
infocenter.nordicsemi.com/index.jsp
What would...
Hi,
I have modify the payload of the Light Switch example of the NRF MESH SDK. When I send 50 bytes or less, all works fines : the server nodes received all the bytes...
Hi everyone,
I am developping on a custom board using nRF52840, using MCUboot v1.8.99-ncs1 and nRF Connect sdk v1.8.
For development matters, I would like to change the...
