This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
I have made a software serial library for nRF52840 similar to Arduino software serial. It is working fine. nRF52840 has two UARTE instance and one UART instance, As for my...
I've a code that worked fine on nrf52832xxAA chip. I flashed the code to a new chip nrf52832xxAB (less RAM, ROM) and adjusted the scatter file according to sd ble recommendations...
Hi,
How do I get the RSSI of the active ble connection using the nrf connect sdk? I cannot find any examples or documentation.
Thank you
edit:
ok, found this: https...
Hi all,
i'am sending epoch time for example 1641533394 from mobile to nrf52840dk only once ,then i need to update it continuously
so i tried the below link which gets...
Hi team,
I am trying to generate pulses on a GPIO using timer1. The pulse need not to be very accurate.
To start with I used the below given code to generate a clock frequency...
Hello, I try to modify the official circuit of nRF52810 QCAA to test the chip(Offical version file attached below), and It work successfully. However when I copy the same...
While creating a new project in VS Code with NRF Connect SDK, I would like to add the application specific files to my private company git repository. The issue is that I...
Hello,
I am using s112_nrf52_7.0.1 I have the nrfRF5 SDK and I built a custom application using BLE.
When trying to test it I use the example ble_app_hrs and it works...
On the nFR9160, the modem is drawing more power when it can't connect to a tower and is causing the battery to drop below the rail, causing our device to switch off. Is there...
Hi,
I discovered that when I use the 'write' button in the nrf connect programmer, that it completely overwrites the whole program (similar to erase&write). Before I didnt...
I am developing a proof of concept for a device however I have some questions regarding the Zephyr display libraries, I have a wave share display with no driver such as SSD16XX...
Hi, Is there a limitation on the available MCLK frequency for the NRF9160 I am trying to configure I2S master with 16K sampling, 16bit, and after i2s_configure() SDK info...
Hi,
I am now working on communication part between esp32 and nrf5340. I want to send the data via ble from nrf5340 and it will receive by esp32. Now, I can able to connect...
Hi sir
We're now working with the nrf52840 DK board, and we want to use two i2c at the same time, but I'm having trouble with one i2c working properly, which means twi1...
Dear Sir.
I use these commands to connect the Modem ON and OFF.
I need to know if the result of the these commands the Modem communicates with the Cell tower ?
Please...
