Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello All,
SDK -- 15.3.0
I want to interface MX25r6435f with NRF52810 so i saw some older queries regarding this Flash driver,
so some where i saw that in sdk QSPI example...
Hi!
We are working with the nrf5340 (custom board-revision QKAAAB) and we are facing an issue when resetting the application. If we add some functionalities to a bluetooth...
hello,
i am using nrf52832 with sdk 15.2 and i want to advertise my beacon like the above picture how can i change the length type and values i can understand the app beacon...
Once paired & Bonding is completed. If neither side pairing & Bonding information is deleted. After restart the device is not advertising again. We are getting PM_EVT_CONN_SEC_FAILED...
Hi, Good afternoon. Some Questions.
1.
Is the Enhanced ShockBurst (ESB) protocol applicable to the nRF5340? I'd appreciate it if you could give me details on how to get...
The nrf52833_peripherals.h file has the P1_PIN_NUM set to 10 but the pca10100.h file has ARDUINO 8-13 pins mapped to port 1, pin 17 to 23. This cannot be correct and causes...
Hey all,
I want to try the Asset Tracker v2 (NCS v1.6.0) Application in AWS, so I followed this guide .
When I try to create the CA certificates and register them in AWS...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
I am new to BLE.
My question is similar to the one below.
https://devzone.nordicsemi.com/f/nordic-q-a/22596/nrf51822-central-connect-and-communicate-with-2-peripherals...
I am using the nfc_writable_ndef_msg example in the SDK to write from my phone to the board using NFC. I get it working successfully however, I am also trying to add code...
