I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi, I've a timer configured by gpiote to capture with a second 'overflow' capture should the signal stop. I'm not using an interrupt instead the CC[0] value is being used...
I have seen the same issue reported.
nRF52840 DK does not appear as a removable drive named "JLINK"
Done the following.
1- My laptop has only one USB port. So I have...
Hi there, I'm controlling the nrf9160 with a esp32 and I'm wondering if you have an recommended libraries for forming AT commands and parsing the return messages?
I'm running through the nrf9160 dk startup guide and I've updated the application and modem firmware. However, it does not look like the application is accepting AT commands...
I have a BL654-DVK (nRF52840) and BL653-DVK (nRF52833). I have a custom program modified from an example that runs and debugs properly on the nRF52840, and am trying to port...
Hi,
We connect our external Board through P20 from EVB NRF52-DK everything goes well.
We are trying to do the same setup on other computer and we get failures to flash...
Hi,
I'm having trouble with debugging the nRF5340. I'm only using the network core and hence use the empty_app_core project for the app core.
The problem i'm facing is...
Hello,
Ubuntu 20.10, nRfConnect v3.6.1, Programmer 1.4.8. Running appimage.
I get:
" Could not fetch memory size of target devkit: Error: Error occured when get library...
hi,
i am working on " ble_app_multilink_central " in ble central . i have connected two peripheral devices .how to include uart in "ble_app_multilink_central" example code...
I have an issue with getting the I/Os correctly setup for antenna switching.
I am running the radio_test example code with the following modifications.
So far, I have...
Hello
I am new to all of this and am wondering if this is possible, and if anyone can point me in the right direction if it is. I am looking to create an open source project...
Hi DevZone Team,
when I use west to configure a project, build/zephyr_settings.txt always contains
"BOARD_ROOT":"/home/user/test/nrf" "DTS_ROOT":"/home/user/test/nrf"...
I am facing one another problem basically i am sending some AT command from central to peripheral but after some time its hang and wait app_erroc. c (__disable_irq();->while...
Hello, I commissioned a factory to make a sample card reader for my company, they didn’t configure everything, because the SDK given to us allows the device to read-only NFC...
Hi
I have a setup with one device and one host, and I want to send data return to the device, but I'm not getting the nrf_gzll_host_rx_data_ready callback no the host. ...
