Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi
There are already several questions regarding UART clock source, e.g. that one for nrf52 where it is stated that the peripherial always take the 16 MHz clock.
Is this...
Hi, the nRF21540 FEM is out for quite a long time. However, there is still no direct support in NCS. Fortunately. some work has already been done. This PR introduces the FEM...
I want to add some logging to my nrf5340 net application and I'm having some troubles.
I have the following in my main.c: #include <logging/log.h> LOG_MODULE_REGISTER...
Its clear there is little interest in this DK compared to the nRF52 version. I got instructions for that platform that actually worked.
Not so for the nRF51 DK. But I am...
I am using FreeRTOS and some of the commands there have two flavors: for using in regular code flow and when are executed from an ISR, but in nRF SDK components and examples...
Hi All,
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer.
My setup: HW: PCA10040 SDK: 17.0.2 Project: nRF5_SDK_17.0.2_d674dde...
Hi,
I followed all the steps to get NCS up and running with SEGGER Embedded Studio. However, when I try to open an example, I get this error:
Including boilerplate ...
Hi all,
I am currently working with nRF52832 boards, and I am trying to save some values in my flash memory. I have already created a code for this purpose and I am able...
Hi, I'm currently trying to understand multi-Link and Immediate Alert Server Application (ias) examples in SDK 17.
While I'm analyzing them, I got some questions:
Q1)...
Hi,
I am working on the nRF52832 ,why i can't able to set the low 7.5 ms interval . I am getting the error at ble_advertising_start . Do I want to change anything else?...
We are preparing our nRF52 product for the unintentional radiator test. Currently, the SoftDevice is enabled and we have the low power mode disabled with the following changes...
Hi,
Looking for some guidance on how to use the 'cryptographically secure random number generator' in a Zephyr/nRF Connect SDK application on an 52840
Is this a supported...
Hi sometimes it happen with my nrf52832 based device. The common way I am programming firmware during development is next:
nrfjprog --program fw.hex --sectorerase --verify...
Hi,
I am working on the nRF52832 ,If i want my data to be transmit every 7.5ms then what should I set the minimum connection interval and maximum connection interval ? please...
Regarding that the nrf52811 is able to use direction finding, there is any example for configure a tag with the nrf52811 to be located? Did nordic finally release any AoA...
