hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Up until now I have been the sole firmware developer and the keeper of the keys for our product.
Our scrappy little startup has expanded and is now bringing on additional...
Hi,
Problems I am having with PWM:
1. Using app_PWM and GPIOTE to start and stop the PWM: When button is pressed, GPIOTE handler sets a flag that is polled to start the...
I am using Timer0 and Timer with GPIOTE and PPI to output 2 clocks on 2 pins.
Both timer settings are identical (for troubleshooting). Only timer-0 can be generated at the...
I am working with nRF Connect SDK using an nRF52840 DK. And I want to realise both BLE mesh and FOTA upgrade. FOTA upgrade example SMP Server Sample works properly for Bluetooth...
To parse information from strings I want to use sscanf().
Currently I have this small test program:
And in the prj.conf I have CONFIG_NEWLIB_LIBC=y defined.
This program...
Hi, At power on lots of MUCBoot prints pop out of the UART:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1 *** <inf> mcuboot: Starting bootloader <inf> mcuboot: Primary image...
Hello -
We are developing an application for nRF52840, using the v17.0.0 SDK. The application is running on FreeRTOS. We need to power off all the RAM and use the RTC...
Hi, I am trying to get bootloader to jump to either application 1 or 2 base on button states when booting. I am not sure how do it properly. One of the applications is using...
I created an Azure IOT Hub and simulated a X.509 device using C and device SDK for Azure .
No problems here.
Then I run sample nRF9160: Azure Iot Hub and receive the...
I am using 2 counters, one to produce the 4MHz, and the other for the 62.5KHz, to drive I2S module.
I need to find a way to stop the first counter (4MHz) after it produces...
Hi All,
Currently I am using SDK_17.0.0 for nRF52832 with Softdevice S132_V7.0.1. I come to know about release of SDK_17.0.2 with highly recommendation to migrate from SDK_17...
Hi. I have the following code, I am attempting to read AIN0 on pin 4 (P0.02).
I am watching the result whilst debugging the application on DK52, and it is a random value...
I'm currently facing a problem while using FreeRTOS. I've created a task, but that tasks freezes the board at this line :
without FreeRTOS this piece of code works...
I've noticed three PCA10059 Dongles have failed in the past week. One on my desk and the two on a co-worker's desk. Its the same failure mode where everything appears to function...
Hi,
We are going to evaluate: nRF52840 with a large NOR flash. This Flash has two options: 3.0V / 50 mA max, Or 1.8V / 50 mA max. We prefere to use the 1.8V type, as this...
