Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Imagine i have a client which sends message to a gateway and i set a TTL for the shortest path . If one of the node is not functioning how will the mesh reroute the message...
nrf52840
sdk for thread and zigbee 2.0
windows
segger studio
in example simple coap cilent and simple coap server
I create my own packet error test through coap...
Hi All,
Currently in my project i'm using hard core delay and delay is custom i.e some places i have used millisecond and in some places used microsecond and in sec.But...
Hi all,
I may need some guidance on the finite state machine method which found an example in app_level.c (from nRF5 SDK for Mesh v3.1), please see my question on below...
What is the minimum specified voltage required on ENABLE (Pin 101) for proper operation of the nRF9160 SIP? Is it the traditional 0.7 VDD, or is it permissible to use a lower...
Hello, I work with an nRF52832 DK and I want to test the example code "ble_app_uart_coexist" . I use the S132 softdevice, SDK 15.3.0 and version 3.1.0 of the mesh for this...
Hi
I used the SDK14 with nRF52832, and carry out the blinky example. When using the Android, the BLE device could be found, but the IOS cannot scan the device. So could...
Hi,
So I am working on NRF52832 with S132 6.1.0 and SDK 15.2.0 mtu and data lenght testings. During that time I was unable to change mtu multiple times while connected ...
I have a ble device and want to write a byte array in nRF Master Control Panel. Firstly, it can be written. But i don't know ho w to input it. My byte array is [-128, -64...
Hi,
I looked at this comment.
If this function (sd_power_system_off) is executed, can I wake up the device again with a soft reset?
If not,
What is a function that...
Hi,
In the documentation nFR523832_PS_v1.4, on page 107, the registers HFCLKSTAT and LFCLKSTAT when in reset mode, indicates that the LFCLK is not runing, and neither the...
Hi Everyone
I am trying to use 2 instances of SPI SPI0 AND SPI2 for Epaper Display and MCP2515 CAN bus module respectively.
Epaper and CAN are working fine if one of them...
I am using NRF52 SDK version 15.3. I am using the app_usbd_cdc_acm module to create a virtual serial port between an NRF52840 DK and a Linux laptop. I am sending messages...
I'm looking into migrating my project from gcc/make to Segger Embedded Studio, because I have some tricky debugging to do and SES should be a bit easier to use than GDB for...
