Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi!
I am evaluating BLE UART Demo with longe range (BLE_GAP_PHY_CODED).
Max. data throughput (using different parameters for ATT_MTU size and connection inverval) seems...
Hello,
I am designing a wearable using the nRF52810 chip and would like to ask if there are any recommended touchscreens to be used? My main concerns are
SPI bus (at...
GCC linker is capable to generate elf file with a given value for UICR->APPROTECT register with a simple script:
This feature allows generating "always protected firmware...
i'm using this dongle USB840F based on nRF52480.
i'm using usbd_ble_uart_freertos (SDK 15.2) example, the usb port is detected and i can read from it , but it doesn't advertise...
Hello
I'm surprised to see this kind of power profile when the device is in advertising mode.
The 3 TX steps for the 3 canals of advertising haven't got the same max...
Good day,
I wish to adapt the Eddystone Beacon example for nRF51822 with S130 in e.g.:
..\nRF5_SDK_12.3.0\examples\ble_peripheral\ble_app_beacon\pca10028\s130\armgcc ...
In my application, the nRF52840 dongle is hard-wired via UART port pins to the UART interface of a Wi-Fi gateway host board. I need the nRF52 application to restart when it...
As a final step to the legitimate dual bank-based application DFU , the existing application will be replaced by the new application.
What happens if an internal error...
Hello,
Is it somehow possible to output a 13.56 MHz signal from the nRF52 ?
Yes, I KNOW: Similar questions have been asked many times. The nRF52 cannot drive an 13.56Mhz...
Hi,Nordic Teams:
I have emergent proble ,can you help me?
1.in light_switch example provisioner,there is some code below:
2.when provisoning ,we can setup a node to...
So I run SDK 15.0. I have a notification channel, and I want to transmit some data on it.
I run this code
hvx_params.handle = gatt_notify_handlers[index].gatt_handle;...
I'm using the nRF52840 to interface with an existing 802.15.4 network. For reasons decided long before I became involved, the messages exchanged are MAC command frames, not...
Hi,
I am testing BLE throughput between NRF52832 and iPhone XR using S132 stack. I am able to get maximum of 400Kbps. Is there a way to achieve throughput better than...
Hi,
I am trying to design the transmission lines based on the reference board design from Nordic.
I opened up the Altium layout file for the board which I downloaded...
