I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
We are using nRF51822, SDK12.3, pca10028, S130 with "Red Bear BLE Nano V1.5" board. We try also in nRF51DK and our own board (designed by us) and the issue is the same...
Hey,
I'm trying to solve the issue of connecting a central device (nRF52832 running experimental ATT MTU example) with a particular peripheral device (also, nRF52832 running...
Ever since you guys updated the site months ago, I haven't been able to post anything from a non-mobile device. I've tried multiple browsers and the only ones that work consistently...
I'm developing a peripheral with s132 v5.1.0 that supports multiple concurrent connections. I've looked at section 15 of the SoftDevice Spec and I have a couple of questions...
Dev Software: Nrf mesh sk 2.1.1 along with sdk 15 on Windows.
IDE: Segger Embeded Studio
Soft Device: s132
Device: nRF52382
Hi,
Is there a way where i can use the...
hi,
I am using nRF52832 with SDK 12.2.0 and S132 softdevice. I am faciing some issues with the memory usage. When I declared an array of size 50 bytes, my application behaves...
Hi Nordic Support Team,
I try to go to low power mode and coming back but can't at all.
I have used the example pwr_mgmt in sdk 12.3.0, but when try to use its function...
I am using the nRF51822. I am using the regulator (not the DC/DC) connection and am not using the low-power (1.2V) mode. All supplies are 3.3V.
Additionally, I am only using...
I want to make a small sensor that will wake up every once in a while, turn on advertising for a second or two and then go back to sleep again.
I'm trying to figure out...
Hello,
I've using mynewt to develop an application using the nRF52 DK (PCA10040 1.2.1, IC marking: N52832 QFAAB0 1701FH). I've been using their basic hello world application...
Hi,
I would like to update advertising packet, but every time I get error NRF_ERROR_INVALID_STATE in function sd_ble_gap_adv_set_configure(). I set all parameters properly...
Hi,
I am connecting the nRF52832 UART (on my nRF52 DK) to an external device, which by default uses 9600 baud rate (but can be reconfigured differently).
In the case...
I have a board populated with the nRF51822 and associated components for the application.
I am able to flash the device successfully and successfully verify the flash. ...
